Kenwood 6070 Instruction Manual - Page 23
Preparing for surround sound, Speaker settings - vr thx
View all Kenwood 6070 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 23 highlights
Preparing for surround sound Speaker settings To enable you to obtain optimum enjoyment from the receiver's listening modes, make sure to complete the speaker settings (subwoofer, front, center, and surround speakers) as described below. POWER ON/STANDBY (VR-6070) ON/STANDBY (KRF-X9060D) SETUP MULTI CONTROL POWER ON/OFF (KRF-X9060D) SET UP POWER Joystick (MULTI CONTROL 5 / ∞, DOWN 2 / UP3) 1 Turn on the power to this receiver by pressing the POWER ON/STANDBY (for VR-6070) or POWER ON/OFF and ON/ STANDBY (for KRF-X9060D) key or POWER key. 2 Press the SETUP key to enter the SETUP mode. The Surround Back and Subwoofer speaker output selections are displayed as follows: 1 6ch AMP SB : Surround Back/Subwoofer speaker terminal will output SB sound. Surround Back pre out will have output from SBL only. 2 6ch AMP SW : Surround Back/Subwoofer speaker terminal will have no sound. Surround Back pre out will have output from SBL and SBR. 3 6ch AMP OFF : It is not advisable to use Surround Back/ Subwoofer speaker terminal for this selection. Use the MULTI CONTROL knob or Joystick (5/∞) to select the speakers. Press the SETUP key to proceed to the next SET UP selection. Use M/? keys or Joystick (2/ 3) for the following displays. 1 SP SETUP 2 TEST TONE 3 BASS PEAK 4 SP DISTANCE 5 DISP MODE 6 EXIT The flow of the SET UP is as follows: SP SETUP Subwoofer Front Center Surround Surround Back Surround Mix Subwoofer Re-mix TEST TONE BASS PEAK T. TONE T. TONE AUTO MANUAL L L C R C SR SB R (SBR/SBL) SL SR SW SB (SBR/SBL) SL SW SP DISTANCE Front Left Center Front Right Surround Right Surround Back (Surround Back Right/Left) Surround Left Subwoofer DISP MODE Display Selector Display Listen EXIT 3 Select a speaker system. 1 Select the SP SETUP and press the SETUP key again so that the subwoofer setting indication "SUBW ON" appears. SP MUTE OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6 THX L ACTIVE EQ. MATRIX C SW R A B CLIP COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII Surround EX LFE SL S SB SR RDS RTY AUTO MEMO STEREO TUNED 2 Use the MULTI CONTROL knob or Joystick (5/∞) to select the appropriate subwoofer setting. 1 SUBW ON : Subwoofer setting mode to the receiver is ON. 2 SUBW OFF : Subwoofer setting mode to the receiver is OFF. • The initial setting is "SUBW ON". • When the setting "SUBW OFF" is selected, the front speakers are automatically set to "FRNT LARGE" and the procedure skips to step 6. Before step 6, press the SETUP key to accept the setting. • When subwoofer output sound is required, select "FRNT NML/ THX", or select both "FRNT LARGE" and "SW RE-MIX ON". • After setting SW (subwoofer) from OFF to ON, 6ch AMP setup display will appear to enable you to re-select either SW, SB or OFF from the surround back or subwoofer speaker terminal. 3 Press the M key or Joystick (3) to accept the setting. • The front speakers setting indication "FRNT" appears. SP MUTE OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6 THX L ACTIVE EQ. MATRIX C SW R A B CLIP COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII Surround EX LFE SL S SB SR RDS RTY AUTO MEMO STEREO TUNED 4 Use the MULTI CONTROL knob or Joystick (5/∞) to select the appropriate front speakers setting. 1 FRNT LARGE : Large front speakers are connected to the receiver. 2 FRNT NML/THX : Average size front speakers are connected to the receiver. • For "FRNT LARGE" selection, no sound will be heard from subwoofer speaker even when it is set to ON. However, if you select "SW RE-MIX ON" when subwoofer is selected, you will be able to hear sound from the subwoofer. When in STEREO mode, the sound goes directly to front speaker. 5 Press the M key or Joystick (3) to accept the setting. • The center speaker setting indication "CNTR" appears. 6 Use the MULTI CONTROL knob or Joystick (5/∞) to select the appropriate center speaker setting. If you selected "LARGE" as the front speakers setting, 1 CNTR LARGE : A large center speaker is connected to the receiver. 2 CNTR NML/THX : An average size center speaker is connected to the receiver. 3 CNTR OFF : Center speaker setting mode to the receiver is OFF. If you selected "NML/THX" as the front speakers setting, 1 CNTR NML/THX : Center speaker setting mode to the receiver is ON. 2 CNTR OFF : Center speaker setting mode to the receiver is OFF. 7 Press the M key or Joystick (3) again to accept the setting. • The surround speaker setting indication "SURR" appears. Continued to next page. 23 EN