Kenwood 6070 Instruction Manual - Page 25

Preparing for surround sound 5 Adjust the bass peak level. A restriction is put on the low frequency so that the bass peak level will not go higher than the acceptable level when the volume is increased. If subwoofer speaker is OFF, the limitation will affect the low frequency of the front left and right speakers 1 Press the M/? keys or Joystick (2/3) to select BASS PEAK and press the SETUP key. SW LFE SP MUTE OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6 THX ACTIVE EQ. MATRIX A B CLIP COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII Surround EX RDS RTY AUTO MEMO STEREO TUNED 2 Use the MULTI CONTROL knob or Joystick (5/∞) to adjust the bass peak level to -30dB. • The adjustment range is from - 30dB to 0dB and OFF. 3 For optimum bass peak level, keep increasing the bass peak level by using the MULTI CONTROL knob or Joystick (5/∞) while test tone is being output until clip sound is heard from the subwoofer or front speaker. SW LFE SP MUTE OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6 THX ACTIVE EQ. MATRIX A B CLIP COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII Surround EX RDS RTY AUTO MEMO STEREO TUNED 4 Press the SETUP key to accept the setting. 6 Input the distance to the speakers. 1 Press the M/? keys or Joystick (2/3) to select the SP DISTANCE on setup displays and press the SETUP key. 2 Measure the distance from the listening position to each of the speakers. Jot down the distance to each of the speakers. Distance to Front left speaker (L) : ____ feet (meters) Distance to Center speaker (C) : ____ feet (meters) Distance to Front right speaker (R) : ____ feet (meters) Distance to Surround right (SR) : ____ feet (meters) Distance to Surround back right (SBR) : ____ feet (meters) Distance to Surround back left (SBL) : ____ feet (meters) Distance to Surround left (SL) : ____ feet (meters) Distance to Subwoofer (SW) : ____ feet (meters) 3 Use the M/? keys or Joystick (2/3) to select the speakers and the MULTI CONTROL knob or Joystick (5/∞) to adjust the distance to the front speakers. The speaker indicator to be adjusted blinks. SP MUTE OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6 THX L ACTIVE EQ. MATRIX C SW R A B CLIP COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII Surround EX LFE SL S SB SR RDS RTY AUTO MEMO STEREO TUNED Indication in feet Indication in meters • The allowable setting range is 1 to 30 feet (0.3 to 9.0 m), adjustable in 1 foot (0.3 m) increments. 4 Repeat steps 3 to input the distance for each of the speakers. 5 Press the SETUP key again to return to main set up displays. • The speakers you have selected should appear on the display. Confirm that all the speakers have been correctly selected. 7 Select the display mode. 1 Press the M/? keys or Joystick (2/3) to select the DISP MODE. 2 Press the SETUP key for the following displays: 1 DISP SELECTOR : Displays the current input selector. 2 DISP LISTEN : Displays the current listen mode. 3 Use the MULTI CONTROL knob or Joystick (5/∞) to select the display mode. SP MUTE OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6 THX L ACTIVE EQ. MATRIX C SW R A B CLIP COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII Surround EX LFE SL S SB SR RDS RTY AUTO MEMO STEREO TUNED 4 Press the SETUP key again to accept the setting. 5 Use the M key or Joystick (3) to select EXIT. SP MUTE OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6 THX L ACTIVE EQ. MATRIX C SW R A B CLIP COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII Surround EX LFE SL S SB SR RDS RTY AUTO MEMO STEREO TUNED 6 Press the SETUP key to exit the SET UP mode. Input level adjustment (analog sources only) If the input level of an analog source signal is too high, the CLIP indicator will blink to indicate the source signal. Adjust the input level. SP MUTE OPTICAL 6CH INPUT AUTO DETECT CINEM ACTIV L C SW R A B CLIP COAXIAL ANALOG 96kHzfs DSP M LFE SL S SB SR 1 Use the Input Selector keys to select the source of which the input level you want to adjust. • You can store a separate input level for each input source. 2 Press the SOUND and M/? keys or Joystick (2/3) repeatedly until the "INPUT" indication appears. 3 Use the MULTI CONTROL knob or Joystick (5/∞) to adjust the input level. SP MUTE OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6 THX L ACTIVE EQ. MATRIX C SW R A B CLIP COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII Surround EX LFE SL S SB SR RDS RTY AUTO MEMO STEREO TUNED • The adjustment mode is displayed for approximately 8 seconds. • The input level may be adjusted to any one of three settings: 0dB, -3dB, and -6dB. (The initial setting is 0dB.) 4 Press the SOUND key again to return to the input indication. 25 EN