Kenwood 6070 Instruction Manual - Page 24
Preparing for surround sound, Adjust the speaker volume level., Use the MULTI CONTROL knob or Joystick - manual receiver
View all Kenwood 6070 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 24 highlights
Preparing for surround sound 8 Use the MULTI CONTROL knob or Joystick (5/∞) to select the appropriate surround speaker setting. If you selected "LARGE" as the center speaker setting, 1 SURR LARGE : Large surround speakers are con- nected to the receiver. 2 SURR NML/THX : Average size surround speakers are connected to the receiver. 3 SURR OFF : Surround speaker setting mode to the receiver is OFF. If you selected other than "LARGE" as the center speaker setting, 1 SURR NML/THX : Surround speaker setting mode to the receiver is ON. 2 SURR OFF : Surround speaker setting mode to the receiver is OFF. • When the setting "SURR OFF" is selected, the procedure skips to step #. 9 Press the M key or Joystick (3) again to accept the setting. • The surround speaker setting indication "SB" appears. 0 Use the MULTI CONTROL knob or Joystick (5/∞) to select appropriate surround back speaker setting. If you selected "LARGE" as the surround speaker setting, 1 SB NML/THX : Average size surround back speaker is connected to the receiver. 2 SB LARGE : Large surround back speaker is connected to the receiver. 3 SB OFF : Surround back speaker setting mode to the receiver is OFF. SP MUTE OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6 THX L ACTIVE EQ. MATRIX C SW R A B CLIP COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII Surround EX LFE SL S SB SR RDS RTY AUTO MEMO STEREO TUNED If you selected other than "LARGE" as the surround speaker setting, 1 SB NML/THX : Surround back speaker setting mode to the receiver is ON. 2 SB OFF : Surround back speaker setting mode to the receiver is OFF. • After setting SB (surround back) from OFF to NML/THX, 6ch AMP setup display will appear to enable you to re-select either SW, SB or OFF from the surround back or subwoofer speaker terminal. ! Press the M key or Joystick (3) again to accept the setting and "SURR:MIX" appears. • Surr:mix is when the SL and SR speakers signals are mixed to produce sound from the surround back speaker which would enable the listener to enjoy sound coming from the back. SP MUTE OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6 THX L ACTIVE EQ. MATRIX C SW R A B CLIP COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII Surround EX LFE SL S SB SR RDS RTY AUTO MEMO STEREO TUNED @ Use the MULTI CONTROL knob or Joystick (5/∞) to select the following. 1 SURR:MIX ON : Surround mix setting mode to the receiver is ON. 2 SURR:MIX OFF : Surround mix setting mode to the receiver is OFF. • If surround back speaker is turned OFF, SURR:MIX setting is not visible and the procedure skips to step #. 24 EN # Press the M key or Joystick (3) again to accept the setting. • The subwoofer re-mix setting indication "SW RE-MIX" appears. $ Use the MULTI CONTROL knob or Joystick (5/∞) to select the appropriate subwoofer re-mix setting. 1 SW RE-MIX ON : Subwoofer re-mix setting mode to the receiver is ON. 2 SW RE-MIX OFF : Subwoofer re-mix setting mode to the receiver is OFF. • If subwoofer is turned OFF, subwoofer re-mix setting is not visible. % Press the SETUP key again to return to the main setup displays. • The receiver enters the speaker volume level adjustment mode. • In steps 4 and 5, indications appear only for the selected channels of the speakers that require adjusting. 4 Adjust the speaker volume level. From your usual listening position, adjust the volume levels. The volume levels from each speaker should be the same. 1 Press the M/? keys or Joystick (2/3) to select TEST TONE. 2 Press the SETUP key for the following displays: 1 T.TONE AUTO 2 T.TONE MANUAL 3 The selection of AUTO/MANUAL TEST TONE is done by the MULTI CONTROL knob or Joystick (5/∞). Press the SETUP key again to begin TEST TONE. Use the MULTI CONTROL knob or Joystick (5/∞) to adjust the volume level of the test tone output from the speaker channel to be adjusted. For AUTO selection, the first test tone is heard from the front left speaker for 2.5 seconds. The next test tone is heard from the speakers in the following sequence for 2 seconds each. When the 6ch AMP SB has been selected. LEFT CNTR RIGHT SR SUBW SL SB When the 6ch AMP SW or OFF has been selected. LEFT CNTR RIGHT SR SUBW SL SBL SBR The channel indication blinks while the test tone is being output. SP MUTE OPTICAL 6CH INPUT AUTO DETECT CINEMA EQ. DTS. DOLBY DIGITAL STEREO NEO:6 THX L ACTIVE EQ. MATRIX C SW R A B CLIP COAXIAL ANALOG 96kHzfs DSP MODE DISCRETE PRO LOGIC LOUDNESS CSII Surround EX LFE SL S SB SR RDS RTY AUTO MEMO STEREO TUNED • If you change the volume level settings for the speakers while listening to music, the settings referred to on this page are also changed. ° • If the speaker setting selects are OFF, the speaker level settings are reset. For MANUAL selection, press the M/? keys or Joystick (2/3) each time to select the speaker channel. 4 Press the SETUP key again. • The test tone is turned off and return to the main setup displays.