Konica Minolta magicolor plus magicolor plus Copyboard M-12S/M-12W/M-125 User - Page 11

Changing the Height of the Unit, CAUTION

Get Konica Minolta magicolor plus PDF manuals and user guides View all Konica Minolta magicolor plus manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Names of the Parts Changing the Height of the Unit This is the height adjustment when setting up the copyboard on the optional stand. The stand height can be adjusted to 3 levels by 100 mm. CAUTION • Please have 2 or more persons lift the Copyboard when installing it or making a height adjustment. If the unit is dropped or falls over, this could cause unforeseen injury. • When a printer is mounted on the copyboard, remove the printer before performing this procedure. Failure to do so could result in injury due to unexpected falling or tipping. • Unplug the power plug from the wall power outlet and remove the power cord from the stand's cable cover before performing this procedure. Failure to do so could result in injury due to the stand tipping over unexpectedly. Please lock the casters by pressing the lower portion of the lock buttons of them. (1) Unplug the AC power adapter's power plug from the wall power outlet and remove the power cord from the stand's cable cover. (2) Remove the printer from the printer table. Disconnect the USB plug from the printer and the DC power plug, loosen the printer guide's fixing screws and remove the printer. (3) Remove the two locking screws (located at the left and right sides). (4) Change the hole position of the Copyboard rear frame. The Copyboard will disengage from the hooks when it is lifted up about 1 cm. Fully hook the (2 left and right) installation holes of the main unit rear frame onto the hooks of the stand. If a stay (for preventing shaking) is mounted on the printer table, insert the stay in its original position. (See (7) on page 5 for mounting instructions.) (5) Attach the locking screws to the 2 locations (left and right) and tighten to the rear frames. (6) Return to original by following the steps in reverse. Mounting hole Hook Rear frames lock-screw *The printer may be an option. * Appearance of printer is for illustration purposes. E-11 Stand Cable cover specifically for the stand

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
E-11
Changing the Height of the Unit
This is the height adjustment when setting up the copyboard on the optional stand. The stand height can be
adjusted to 3 levels by 100 mm.
Names of the Parts
Mounting hole
Hook
Rear frames
lock-screw
Stand
Cable cover specifically for the stand
Please lock the casters by pressing the lower portion of the lock buttons of them.
(1) Unplug the AC power adapter's power plug from the wall power outlet and remove the power
cord from the stand's cable cover.
(2) Remove the printer from the printer table.
Disconnect the USB plug from the printer and the DC power plug, loosen the printer guide's fixing screws and remove
the printer.
(3) Remove the two locking screws (located at the left and right sides).
(4) Change the hole position of the Copyboard rear frame.
The Copyboard will disengage from the hooks when it is lifted up about 1 cm.
Fully hook the (2 left and right) installation holes of the main unit rear frame onto the hooks of the stand.
If a stay (for preventing shaking) is mounted on the printer table, insert the stay in its original position.
(See (7) on page 5 for mounting instructions.)
(5) Attach the locking screws to the 2 locations (left and right)
and tighten to the rear frames.
(6) Return to original by following the steps in reverse.
*The printer may be an option.
* Appearance of printer is for illustration purposes.
CAUTION
• Please have 2 or more persons lift the Copyboard when installing it or making a height adjustment.
If the unit is dropped or falls over, this could cause unforeseen injury.
• When a printer is mounted on the copyboard, remove the printer before performing this procedure. Failure to
do so could result in injury due to unexpected falling or tipping.
• Unplug the power plug from the wall power outlet and remove the power cord from the stand's cable cover
before performing this procedure. Failure to do so could result in injury due to the stand tipping over
unexpectedly.