Kyocera ECOSYS FS-2020D FS-2020D/3920DN/4020DN Operation Guide (Basic) - Page 39

Connecting the Power Cord, IMPORTANT, Ready]

Get Kyocera ECOSYS FS-2020D PDF manuals and user guides View all Kyocera ECOSYS FS-2020D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Connecting the Power Cord Install the printer close to an AC wall outlet. If an extension cord is used, the total length of the power cord plus extension should be 5 meters (16 feet) or less. Note Ensure the printer's power switch is off. Only use the power cord supplied with the printer. 1 Connect the power cord to the Power Cord Connector at the rear of the printer. 2 Connect the other end of the power cord to a power outlet. 3 Press the Power Switch to On ( | ). The printer begins to warm up. IMPORTANT If you install the starter toner container and switch on the power, after a moment the message Please wait(Adding toner) is displayed. When the printer is first switched on after toner installation, there will be a delay of approximately 15 minutes before the printer gets ready to print. Once the [Ready] indicator lights, printer installation is complete. Connecting and Printing 3-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Connecting and Printing
3-3
Connecting the Power Cord
Install the printer close to an AC wall outlet. If an extension cord is used, the
total length of the power cord plus extension should be 5 meters (16 feet) or
less.
1
Connect the power cord to the Power Cord Connector at the rear of
the printer.
2
Connect the other end of the power cord to a power outlet.
3
Press the Power Switch to On ( | ). The printer begins to warm up.
Note
Ensure the printer's power switch is off. Only use the power
cord supplied with the printer.
IMPORTANT
If you install the starter toner container and switch
on the power, after a moment the message
Please
wait(Adding toner)
is displayed. When the printer is first
switched on after toner installation, there will be a delay of
approximately 15 minutes before the printer gets ready to print.
Once the
[Ready]
indicator lights, printer installation is complete.