LG 32LD655H Setup Guide - Page 21

Installer Menu (Cont.) • 6 = Scaler Model RJPs: DVI Mode Enables RJP feature for use with reduced cable bundle models. In this mode, when an HDMI/DVI source is connected to the RJP, only digital video is expected via the HDMI cable. Analog audio is provided via separate cable, from the source, connected to an RJP AUDIO IN. If no analog audio cable is connected, tuner audio will be heard. Notes: See Reference section, "RJP Model List and Input Auto-sensing Hierarchy." If RJP AVAILABLE is set to 1, 2, 5, or 6, item 040 AUTO CAMPORT is automatically set to 0. Settings 1, 2, 5, and 6 allow the lodge staff to customize each TV's RJP setup based on customer requirements. 094 - SAP MENU EN (2nd Audio Program) Set to 1 to enable SAP feature on Function menu, if Function menu is available. Set to 0 to disable SAP feature on Function menu, if Function Menu is available. 096 - DEF. ASP. RATIO (Default Aspect Ratio) Selects default aspect ratio at power up. • Set to 0 for Set By System. • Set to 1 for 4:3. • Set to 2 for 16:9 (Factory Default). • Set to 3 for Just Scan. • Set to 4 for Zoom. Note: Only applies if item 106 ASP RATIO LOCK is disabled, set to 0. 099 - BACK LIGHTING Sets the TV screen brightness at power up. Default setting is 202. • 1 - 100 Static Back Lighting (1 = Dimmest picture, 100 = Brightest picture) • 101 - 200 Dynamic Back Lighting (101 = Dimmest picture, 200 = Brightest picture) • 201 Automatic Static Back Lighting • 202 Automatic Dynamic Back Lighting • If set between 101 and 200, the TV automatically controls back lighting depending upon the picture level of the current program. • If set to 201, the TV automatically controls back lighting depending upon external spectral sensitivity. • If set to 202, the TV automatically controls back lighting depending upon external spectral sensitivity and the picture level of the current program. • If set to 255, back lighting is controlled via the Picture settings in the TV's setup menus. 102 - ATSC BAND Sets up TV to receive different types of incoming signals: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC, 4=Same as NTSC. 103 - ATSC TUNE MODE Sets ATSC tuning mode: Default set to 1 for Physical Channel scan. Set to 0 for Virtual Channel scan. 104 - START MINOR CHANNEL Sets XXX-XXX digital Minor Start Channel at power up. 0=NTSC. If not 0, number selected is the digital Minor Start Channel number. 106 - ASP RATIO LOCK (Aspect Ratio Lock) Set to 1 to retain previous aspect ratio with power off. Set to 0 to retain default aspect ratio with power off. See item 096 DEF. ASP. RATIO above. 116 - VIDEO MUTE EN (Video Mute Enable) Set to 0 for Normal. Set to 1 for Blank. 117 - FACT DEFAULT (Factory Default) Set to 0 for normal. Set to 1 to load presets of all Installer Menu item settings. Warning: If set to 1, this will reload the factory defaults and clear the Channel List, including any assigned channel icons and custom channel labels. 118 - POWER SAVINGS Default is set to 3. When the TV is in Standby mode, the MPI card slot is powered by the Standby power supply and embedded b-LAN is not powered. When the TV is in Power On mode, the MPI card slot is powered by the main 12V power supply and embedded b-LAN is powered. Note that the TV must be turned ON in order to communicate with the Embedded b-LAN module for configuration and control when POWER SAVINGS is set to 3. Note: MPI cards with b-LAN technology-LMT7Z5, LMT7Z7, LMT7Z9-are NOT supported on TVs in which the b-LAN module is embedded. Warning for LD65xH TVs: If an MPI card is installed, POWER SAVINGS must be set to 1. The default setting does not support this feature. • 1 = MPI card slot Standby Mode power provided from Standby power supply, and Embedded b-LAN is always powered. • 3 = MPI card slot Standby Mode power provided from Standby power supply, and Embedded b-LAN is only powered when the TV is turned ON. • 7 = MPI card slot Standby Mode power provided from Standby power supply, and Embedded b-LAN (including the Pro:Centric data tuner) is never powered. Note: See Reference section, "b-LAN Setup & Overview," for further information. 119 - DATA CHANNEL Set to 0 (default) to disable. Set to the RF channel number of the Data Channel for Pro:Centric operation. The TV may take several minutes to load EPG data after AC power is initially applied. 206-4137 21