LG 32LD655H Setup Guide - Page 24

FTG Mode of Operation

Page 24 highlights

FTG Mode of Operation FTG Configuration Overview The following steps outline local FTG configuration of individual TVs. Since these models are equipped with the EBL module, they can also be broadcast configured in FTG Mode by a Free-To-Guest Management Appliance (FMA) head end device. Refer to the Free-To-Guest (FTG) Configuration Application manual and/or the Installation & Setup manual for the FMA device for further information. Note: FTG Configuration Application software is available online at: www.LGcommercial.com/FTGsoftware. 1. Install (if necessary) and launch the FTG Configuration Application (v5.0.0 or higher) on the PC that will be used to configure the EBL. 2. Build a Channel Map using the FTG Channel Map Editor in the FTG Channel Map Configuration Utility (or, if applicable, open an existing FTG Configuration (.rml) file). 3. If not already done, connect the PC to the TV-LINK CFG jack on the rear connections panel using a USB-toTTL serial cable (TTL-232R-5V-AJ). 4. "Write" the FTG Channel Map to the EBL (converts EBL from Pass-through Mode to FTG Mode). 5. "Read" the current FTG Installer Menu settings from the EBL using the FTG Installer Menu Configuration Utility. If necessary to make changes to Installer Menu items, "Write" them back to the EBL in FTG Mode. 6. Save the FTG Channel Map and FTG Installer Menu settings to an FTG Configuration (.rml) file for future use. 7. Tune the TV to a Logical Channel in the FTG Channel Map. LD650H/ LD655H Jack Panel TV-LINK CFG Use for local FTG configuration. HDMI/DVI IN 2 .......... 1 .......... LAN RESET UPDATE GAME CONTROL /MPI TV-LINK OPTICAL CFG DIGITAL VIDEO L/MONO-AUDIO-R AUDIO OUT ANTENNA IN SPEAKER OUT 8 AV IN 1 COMPONENT IN Y PB PR L R RJP INTERFACE RGB IN (PC) AUDIO IN (RGB/DVI) ......... RS-232C IN (SERVICE ONLY) REMOTE CONTROL OUT USB-to-TTL Serial Cable for Connection to PC (47/55LD650H only) Laptop PC LG710H Jack Panel 24 HDMI/DVI IN 2 .......... 1(DVI) .......... RJP INTERFACE TV-LINK CFG Use for local FTG configuration. LAN (SERVICE ONLY) TV-LINK CFG GAME CONTROL OPTICAL DIGITAL AUDIO OUT RESET UPDATE ..R...G.B...(..P.C...) AUDIO (RGB/DVI) RS-232C IN ......... (SERVICE ONLY) SPEAKER OUT 8 REMOTE CONTROL OUT Y PB PR L R RGB IN AV IN 1 VIDEO AUDIO COMPONENT IN R-AUDIO-L/MONO VIDEO USB-to-TTL Serial Cable for Connection to PC Laptop PC 206-4137

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48

24
206-4137
FTG Mode of Operation
FTG Con
guration Overview
Laptop
PC
COMPONENT
IN
RS-232C IN
(SERVICE ONLY)
UPDATE
RESET
AUDIO IN
(RGB/DVI)
.....
....
R
L
P
B
Y
P
R
..........
2
1
HDMI/DVI IN
OPTICAL
DIGITAL
RJP
INTERFACE
VIDEO
L/MONO
-AUDIO-
R
AV IN 1
RGB IN (PC)
.....
.....
.....
LAN
TV-LINK
CFG
GAME CONTROL
/MPI
..........
AUDIO OUT
REMOTE
CONTROL
OUT
SPEAKER
OUT
8
ANTENNA
IN
The following steps outline local FTG configuration of individual TVs. Since these models are equipped with the
EBL module, they can also be broadcast configured in FTG Mode by a Free-To-Guest Management Appliance
(FMA) head end device. Refer to the
Free-To-Guest (FTG) Configuration Application
manual and/or the
Installation & Setup manual for the FMA device for further information.
Note:
FTG Configuration Application software is available online at: www.LGcommercial.com/FTGsoftware.
1. Install (if necessary) and launch the FTG Configuration Application (v5.0.0 or higher) on the PC that will be
used to configure the EBL.
2. Build a Channel Map using the FTG Channel Map Editor in the FTG Channel Map Configuration Utility (or, if
applicable, open an existing FTG Configuration (.rml) file).
3. If not already done, connect the PC to the TV-LINK CFG jack on the rear connections panel using a USB-to-
TTL serial cable (TTL-232R-5V-AJ).
4. “Write” the FTG Channel Map to the EBL (converts EBL from Pass-through Mode to FTG Mode).
5. “Read” the current FTG Installer Menu settings from the EBL using the FTG Installer Menu Configuration
Utility. If necessary to make changes to Installer Menu items, “Write” them back to the EBL in FTG Mode.
6. Save the FTG Channel Map and FTG Installer Menu settings to an FTG Configuration (.rml) file for future use.
7. Tune the TV to a Logical Channel in the FTG Channel Map.
Laptop
PC
REMOTE
CONTROL OUT
SPEAKER OUT
8
VIDEO
L/MONO
COMPONENT IN
VIDEO
AUDIO
R
L
RS-232C IN
(SERVICE ONLY)
UPDATE
RESET
AUDIO
(RGB/DVI)
P
B
Y
P
R
.....
....
..........
2
1(DVI)
HDMI/DVI IN
OPTICAL
DIGITAL
AUDIO OUT
RJP
INTERFACE
RGB IN
R
-AUDIO-
AV IN 1
RGB(PC)
.....
.....
.....
LAN
(SERVICE ONLY)
TV-LINK
CFG
GAME
CONTROL
..........
LD650H/
LD655H
Jack Panel
LG710H
Jack Panel
TV-LINK CFG
Use for local FTG
configuration.
USB-to-TTL Serial
Cable for Connection
to PC
(47/55LD650H
only)
USB-to-TTL Serial
Cable for Connection
to PC
TV-LINK CFG
Use for local FTG
configuration.