LG 60PB4DT-UB Owner's Manual (English) - Page 151
a][ ][Set ID][ ][OK][Data0][Data1], Data2][Data3][Data4][x][a][ ][Set ID], NG][Data0][x], m][b]
View all LG 60PB4DT-UB manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 151 highlights
APPENDIX 150 APPENDIX Data5: 7 Main/Sub Picture 6 Two/One 5 Using Physical 4 3 Part Channel Channel Reserved 2 1 0 Step 0 Main 1 Sub 0 Two 1 One 0 Use x 0 0 0 0 NTSC Air 1 No Use x 0 0 0 1 NTSC Cable x 0 0 1 0 ATSC Air x 0 0 1 1 ATSC Cable_std x 0 1 0 0 ATSC Cable_hrc x 0 1 0 1 ATSC Cable_irc x 0 1 1 0 ATSC cable_auto x 0 1 1 1 x x x x x x 1 1 1 1 Reserved ... Reserved All data are transmitted by Hexadecimal code * Two/One part Channel: 6th bit This bit is used in a cable-ready system. * Using physical channel: 5th bit If the channel band is NTSC air or NTSC cable, channel tuning can be done by only physical channel. In this case, using physical channel bit must be low(0). But if the channel band is ATSC air or ATSC cable, there are two cases that physical channel enable or disable. If the physical channel sending is meaningful, you should set this bit low(0). If the physical channel sending is meaningless, you should set this bit high(1). Example) 1. Analog channel: NTSC cable, channel number(35), main picture Command: ma 00 23 xx xx xx xx 01 attribute(0x01): main picture, two part(it's not mandatory), using physical channel, NTSC cable 'xx' data: don't care major and minor channel number in case analog channel tuning. 2. Digital channel: ATSC air, channel number(don't know physical channel, major(30), minor(3)), sub picture Command: ma 00 xx 00 1E 00 03 A2 attribute(0xA2): sub picture, two part, not using physical channel, ATSC air 'xx' data: don't care analog channel number in case digital channel tuning. 3. Digital channel: ATSC air, channel number(physical(20),major(20), minor(3)), sub picture Command: ma 00 14 00 14 00 03 82 attribute(0x82): sub picture, two part, using physical channel, ATSC air. Acknowledgement[a][ ][Set ID][ ][OK][Data0][Data1] [Data2][Data3][Data4][x][a][ ][Set ID] [ ][NG][Data0][x] 29. Channel Add/Del (Command: m b) To add and delete the channels Transmission [m][b][ ][Set ID][ ][Data][Cr] Data 0: Channel Delete Data 1: Channel Add Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x] 30. Key (Command: m c) To send IR remote key code. Transmission [m][c][ ][Set ID][ ][Data][Cr]s Data Key code: Refer to page 142. Acknowledgement [c][ ][Set ID][ ][OK/NG][Data][x] 31. Input select(Command: x b) (Main Picture Input) To select input source for TV. Transmission [x][b][][Set ID][][Data][Cr] Data 00 : DTV (Antenna) Data 01 : DTV (Cable) Data 10 : Analog (Antenna) Data 11 : Analog (Cable) Data 20 : AV1 Data 21 : AV2 Data 40 : Component 1 Data 41 : Component 2 Data 50 : RGB DTV Data 60 : RGB PC Data 90 : HDMI1/DVI Data 91 : HDMI2 Acknowledgement [b][ ][Set ID][ ][OK/NG][Data][x] 32. PIP Input Select(Command: x y) To adjust input source for sub picture in PIP mode. Transmission [x][y][][Set ID][][Data][Cr] Data 00 : DTV (Antenna) Data 01 : DTV (Cable) Data 10 : Analog (Antenna) Data 11 : Analog (Cable) Data 20 : AV1 Data 21 : AV2 Acknowledgement [y][][Set ID][][OK/NG][Data][x]