Lenovo J110 Hardware Maintenance Manual - Page 121

Remove the drive bay assembly. See Removing and replacing the drive bay assembly

Get Lenovo J110 PDF manuals and user guides View all Lenovo J110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

4. From the front of the chassis, slide the drive bracket to the left until it is free of the retaining clips in the bottom of the chassis. It can now be can be removed from the chassis. 5. Disconnect the signal and power cables from the rear of the hard disk drive. 6. Remove the four screws that secure the hard disk drive to the bracket and remove the drive from the bracket. 7. Position the new drive into the hard disk drive bracket so that the screw holes on each side are aligned and install two screws into each side of the drive. 8. Reconnect the signal and power cables to the rear of the hard disk drive. 9. Position the hard disk drive bracket so that it engages the retaining clips in the bottom of the chassis when you slide the bracket to the right. 10. Slide the hard disk drive bracket to the right until the screw holes are aligned and install the screws. 11. Reinstall the drive bay assembly and connect the power and signal cables to the drives. 12. Go to "Completing the FRU replacement" on page 117. Replacing an optical drive 1. Remove the cover. See "Removing the cover" on page 94. 2. Remove the drive bay assembly. See "Removing and replacing the drive bay assembly" on page 97. 3. Remove the screws that secure the drive in the drive bay assembly. 4. Slide the drive being replaced out the front of the drive bay assembly. 5. Slide the new drive into the bay until the screws holes on each side are aligned and install the screws that secure the drive to the drive bay assembly. 6. Reinstall the drive bay assembly. See "Removing and replacing the drive bay assembly" on page 97. 7. Go to "Completing the FRU replacement" on page 117. Chapter 9. Replacing FRUs (Types 7390, 7391, 7392, 7396, 7397, and 7398) 115

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
4.
From the front of the chassis, slide the drive bracket to the left until it is free of the retaining clips in the
bottom of the chassis. It can now be can be removed from the chassis.
5.
Disconnect the signal and power cables from the rear of the hard disk drive.
6.
Remove the four screws that secure the hard disk drive to the bracket and remove the drive from the
bracket.
7.
Position the new drive into the hard disk drive bracket so that the screw holes on each side are aligned
and install two screws into each side of the drive.
8.
Reconnect the signal and power cables to the rear of the hard disk drive.
9.
Position the hard disk drive bracket so that it engages the retaining clips in the bottom of the chassis
when you slide the bracket to the right.
10.Slide the hard disk drive bracket to the right until the screw holes are aligned and install the screws.
11. Reinstall the drive bay assembly and connect the power and signal cables to the drives.
12.Go to “Completing the FRU replacement” on page 117.
Replacing an optical drive
1.
Remove the cover. See “Removing the cover” on page 94.
2.
Remove the drive bay assembly. See “Removing and replacing the drive bay assembly” on page 97.
3.
Remove the screws that secure the drive in the drive bay assembly.
4.
Slide the drive being replaced out the front of the drive bay assembly.
5.
Slide the new drive into the bay until the screws holes on each side are aligned and install the screws
that secure the drive to the drive bay assembly.
6.
Reinstall the drive bay assembly. See “Removing and replacing the drive bay assembly” on page 97.
7.
Go to “Completing the FRU replacement” on page 117.
Chapter 9
.
Replacing FRUs (Types 7390, 7391, 7392, 7396, 7397, and 7398)
115