Lenovo ThinkCentre A62 (English US/UK) User guide - Page 69

Selecting a startup device, Discard Changes and Exit

Get Lenovo ThinkCentre A62 PDF manuals and user guides View all Lenovo ThinkCentre A62 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

To set the SATA 1, do the following: 1. Start the Setup Utility program (see "Starting the Setup Utility program" on page 59). 2. From the Setup Utility program menu, select Devices → SATA Drives Setup → SATA 1 and press Enter. 3. Select 32 Bit Data Transfer. 4. Select the desired settings and press Enter. 5. Return to the Setup Utility program menu and select Exit → Save Changes and Exit. Note: If you do not want to save the settings, select Discard Changes or Discard Changes and Exit. To set the OnBoard Floppy Controller, do the following: 1. Start the Setup Utility program (see "Starting the Setup Utility program" on page 59). 2. From the Setup Utility program menu, select Devices → Floppy Drive Setup → OnBoard Floppy Controller. 3. Select the desired settings and press Enter. 4. Return to the Setup Utility program menu and select Exit → Save Changes and Exit. Note: If you do not want to save the settings, select Discard Changes or Discard Changes and Exit. Selecting a startup device If your computer does not start up from a device such as the CD-ROM, diskette, or hard disk drive as expected, use one of the following procedures to select a startup device. Selecting a temporary startup device Use this procedure to start up from any startup device. Note: Not all CDs, hard disk drives, and diskettes are bootable. 1. Turn off your computer. 2. Press and hold the F12 key, and then turn on the computer. When the Startup Device Menu appears, release the F12 key. Note: If you are using a USB keyboard and the Startup Device Menu does not display using this method, repeatedly press and release the F12 key rather than leaving it pressed when turning on the computer. 3. Select the desired startup device from the Startup Device Menu and press Enter to begin. Note: Selecting a startup device from the Startup Device menu does not permanently change the startup sequence. Chapter 4. Using the Setup Utility 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
To set the SATA1, do the following:
1.
Start the Setup Utility program (see “Starting the Setup Utility program” on
page 59).
2.
From the Setup Utility program menu, select
Devices
→
SATA Drives Setup
→
SATA 1
and press Enter.
3.
Select
32 Bit Data Transfer
.
4.
Select the desired settings and press Enter.
5.
Return to the Setup Utility program menu and select
Exit
→
Save Changes and
Exit
.
Note:
If you do not want to save the settings, select
Discard Changes
or
Discard Changes and Exit
.
To set the OnBoard Floppy Controller, do the following:
1.
Start the Setup Utility program (see “Starting the Setup Utility program” on
page 59).
2.
From the Setup Utility program menu, select
Devices
→
Floppy Drive Setup
→
OnBoard Floppy Controller
.
3.
Select the desired settings and press Enter.
4.
Return to the Setup Utility program menu and select
Exit
→
Save Changes and
Exit
.
Note:
If you do not want to save the settings, select
Discard Changes
or
Discard Changes and Exit
.
Selecting a startup device
If your computer does not start up from a device such as the CD-ROM, diskette, or
hard disk drive as expected, use one of the following procedures to select a startup
device.
Selecting a temporary startup device
Use this procedure to start up from any startup device.
Note:
Not all CDs, hard disk drives, and diskettes are bootable.
1.
Turn off your computer.
2.
Press and hold the F12 key, and then turn on the computer. When the Startup
Device Menu appears, release the F12 key.
Note:
If you are using a USB keyboard and the Startup Device Menu does not
display using this method, repeatedly press and release the F12 key
rather than leaving it pressed when turning on the computer.
3.
Select the desired startup device from the Startup Device Menu and press Enter
to begin.
Note:
Selecting a startup device from the Startup Device menu does not
permanently change the startup sequence.
Chapter 4. Using the Setup Utility
61