Lenovo ThinkCentre M57 Hardware Maintenance Manual - Page 55

USB port Device Controller failure, FRU/Action

Get Lenovo ThinkCentre M57 PDF manuals and user guides View all Lenovo ThinkCentre M57 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Diagnostic Error Code FRU/Action 006-197-XXX Diskette interface test warning 1. If a component is called out, make sure it is connected and/or enabled 2. Re-run test 3. Replace the component that is called out in warning statement 4. Replace the component under test 006-198-XXX Diskette interface test aborted 1. If a component is called out, make sure it is connected and/or enabled 2. Flash the system and re-test. See "Updating (flashing) BIOS from a CD-ROM or diskette" on page 139 3. Go to "Undetermined problems" on page 62 006-199-XXX Diskette interface test failed, cause unknown 1. Go to "Undetermined problems" on page 62 2. Flash the system and re-test 3. Replace component under function test 006-25X-XXX Diskette interface Error 1. Diskette drive cable 2. Diskette drive 3. System board 015-000-XXX USB port Interface Test Passed No action 015-001-XXX USB port Presence 1. Remove USB device(s) and re-test 2. System board 015-002-XXX USB port Timeout 1. Remove USB device(s) and re-test 2. System board 015-015-XXX USB port External Loopback failure 1. Remove USB device(s) and re-test 2. System board 015-027-XXX USB port Configuration/Setup error 1. Flash the system. See "Updating (flashing) BIOS from a CD-ROM or diskette" on page 139 2. System board 015-032-XXX USB port Device Controller failure System board 015-034-XXX USB port buffer allocation failure 1. Reboot the system 2. Flash the system and re-test. See "Updating (flashing) BIOS from a CD-ROM or diskette" on page 139 3. Run memory test 4. System board 015-035-XXX USB port Reset condition detected 1. Remove USB device(s) and re-test 2. System board 015-036-XXX USB port Register error System board 015-040-XXX USB port IRQ failure 1. Run setup and check for conflicts 2. Flash the system. See "Updating (flashing) BIOS from a CD-ROM or diskette" on page 139 3. System board 015-195-XXX USB port Test aborted by user Information only Re-start the test, if necessary 015-196-XXX USB port test halt, error threshold exceeded 1. Press F3 to review the log file 2. Re-start the test to reset the log file Chapter 7. Symptom-to-FRU Index 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
Diagnostic Error Code
FRU/Action
006-197-XXX
Diskette interface test warning
1.
If a component is called out, make sure it is
connected and/or enabled
2.
Re-run test
3.
Replace the component that is called out in warning
statement
4.
Replace the component under test
006-198-XXX
Diskette interface test aborted
1.
If a component is called out, make sure it is
connected and/or enabled
2.
Flash the system and re-test. See “Updating (flashing)
BIOS from a CD-ROM or diskette” on page 139
3.
Go to “Undetermined problems” on page 62
006-199-XXX
Diskette interface test failed, cause
unknown
1.
Go to “Undetermined problems” on page 62
2.
Flash the system and re-test
3.
Replace component under function test
006-25X-XXX
Diskette interface Error
1.
Diskette drive cable
2.
Diskette drive
3.
System board
015-000-XXX
USB port Interface Test Passed
No action
015-001-XXX
USB port Presence
1.
Remove USB device(s) and re-test
2.
System board
015-002-XXX
USB port Timeout
1.
Remove USB device(s) and re-test
2.
System board
015-015-XXX
USB port External Loopback failure
1.
Remove USB device(s) and re-test
2.
System board
015-027-XXX
USB port Configuration/Setup error
1.
Flash the system. See “Updating (flashing) BIOS
from a CD-ROM or diskette” on page 139
2.
System board
015-032-XXX
USB port Device Controller failure
System board
015-034-XXX
USB port buffer allocation failure
1.
Reboot the system
2.
Flash the system and re-test. See “Updating (flashing)
BIOS from a CD-ROM or diskette” on page 139
3.
Run memory test
4.
System board
015-035-XXX
USB port Reset condition detected
1.
Remove USB device(s) and re-test
2.
System board
015-036-XXX
USB port Register error
System board
015-040-XXX
USB port IRQ failure
1.
Run setup and check for conflicts
2.
Flash the system. See “Updating (flashing) BIOS from
a CD-ROM or diskette” on page 139
3.
System board
015-195-XXX
USB port Test aborted by user
Information only
Re-start the test, if necessary
015-196-XXX
USB port test halt, error threshold exceeded
1.
Press F3 to review the log file
2.
Re-start the test to reset the log file
Chapter 7
.
Symptom-to-FRU Index
49