Lexmark E310 Service Manual - Page 67

Mode 1 Ready LED is blinking.

Get Lexmark E310 - Optra B/W Laser Printer PDF manuals and user guides
UPC - 734646183000
View all Lexmark E310 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

4044-XXX Perform the following steps to change the Parallel Mode 1 setting: 1. Enter the configuration mode. 2. Perform a double click button press five times. This moves to the Parallel Mode 1 item on the configuration menu. The Parallel Mode 1 (Ready) LED is blinking. 3. The current Parallel Mode 1 setting is indicated by the Off/On/ Auto (Press Button) LED. When the LED is off, the Parallel Mode 1 is set to off. When the LED is *on, the Parallel Mode 1 is set to on. Perform a brief button press to select the Parallel Mode 1 setting. 4. Perform a long button press. All LEDs blink once, indicating the setting is saved. 5. Exit the configuration mode by turning the printer power off. Parallel Mode 2 Parallel Mode 2 controls whether or not the parallel port data is sampled on the leading or trailing edge of strobe. The default is to sample on the leading edge of strobe, however, some IBM clone PC's assumes that a printer will sample on the trailing edge. Perform the following steps to change the Parallel Mode 2 setting: 1. Enter the configuration mode. 2. Perform a double click button press six times. This moves to the Parallel Mode 2 item on the configuration menu. The Parallel Mode 2 (Data) LED is blinking. 3. The current Parallel Mode 2 setting is indicated by the Off/On/ Auto (Press Button) LED. When the LED is off, the Parallel Mode 2 is set to sample on trailing edge. When the LED is *on, the Parallel Mode 2 is set to sample on leading edge. Perform a brief button press to select the Parallel Mode 2 setting. 4. Perform a long button press. All LEDs blink once, indicating the setting is saved. 5. Exit the configuration mode by turning the printer power off. Parallel Strobe This setting allows the user to adjust the factory setting for the amount of time strobe is sampled to determine that valid data is Diagnostic Aids 3-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
Diagnostic Aids
3-9
4044-XXX
Perform the following steps to change the Parallel Mode 1 setting:
1.
Enter the configuration mode.
2.
Perform a double click button press five times. This moves to
the Parallel Mode 1 item on the configuration menu. The Parallel
Mode 1 (Ready) LED is blinking.
3.
The current Parallel Mode 1 setting is indicated by the Off/On/
Auto (Press Button) LED. When the LED is off, the Parallel
Mode 1 is set to off. When the LED is *on, the Parallel Mode 1 is
set to on. Perform a brief button press to select the Parallel
Mode 1 setting.
4.
Perform a long button press. All LEDs blink once, indicating the
setting is saved.
5.
Exit the configuration mode by turning the printer power off.
Parallel Mode 2
Parallel Mode 2 controls whether or not the parallel port data is
sampled on the leading or trailing edge of strobe. The default is to
sample on the leading edge of strobe, however, some IBM clone
PC’s assumes that a printer will sample on the trailing edge.
Perform the following steps to change the Parallel Mode 2 setting:
1.
Enter the configuration mode.
2.
Perform a double click button press six times. This moves to the
Parallel Mode 2 item on the configuration menu. The Parallel
Mode 2 (Data) LED is blinking.
3.
The current Parallel Mode 2 setting is indicated by the Off/On/
Auto (Press Button) LED. When the LED is off, the Parallel
Mode 2 is set to sample on trailing edge. When the LED is *on,
the Parallel Mode 2 is set to sample on leading edge. Perform a
brief button press to select the Parallel Mode 2 setting.
4.
Perform a long button press. All LEDs blink once, indicating the
setting is saved.
5.
Exit the configuration mode by turning the printer power off.
Parallel Strobe
This setting allows the user to adjust the factory setting for the
amount of time strobe is sampled to determine that valid data is