Marantz NR1501 NR1501 User Manual - English - Page 20

Advanced Connections

Get Marantz NR1501 PDF manuals and user guides View all Marantz NR1501 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

NAMES AND FUNCTIONS CONNECTIONS BASIC ENGLISH ADVANCED CONNECTIONS CONNECTING THE REMOTE CONTROL JACKS Option 2 RC OUT MONITOR OUT OUT DVD MONITOR OUT BLU-RAY GAME DVD DSS OUT FM (75Ω) GND AM IN DVD IN DSS VIDEO IN VCR L Y PB/CB PR/CR DSS 3 Y PB/CB PR/CR VCR COMPONENT VIDEO 2 PRE OUT R ANTENNA IN DVD IN DSS IN OUT VCR ANALOG AUDIO IN CD 1 IN AUX 2 SUB WOOFER IN OUT REMOTE CONTROL IN DIGITAL AUDIO MODEL NO. NR1501 R - FRONT - L CENTER R - SURR. - L SPEAKER SYSTEMS : 6-8 OHMS R L SURROUND BACK AC IN 1 REMOTE CONTROL IN OUT CD recorder EXTERNAL INTERNAL REMOTE CONTROL IN OUT DVD player EXTERNAL INTERNAL REMOTE CONTROL IN OUT CD player EXTERNAL INTERNAL q You can control other Marantz products through this unit with the remote controller by connecting the REMOTE CONTROL terminals on each unit. The signal transmitted from the remote controller is received by the remote sensor on this unit. Then the signal is sent to the connected device through this terminal. Therefore you need to aim the remote control only at the unit. Also, if a Marantz power amplifier (some models excluded) is connected to one of these terminals, the power amplifier's, power switch is synchronized with this unit's power switch. Set the REMOTE CONTROL SWITCH on the back of other units (not the NR1501) to "EXT." (EXTERNAL) to use this feature. w Whenever external infrared sensors or similar devices are connected to RC-5 IN of the unit, be sure to always disable operation of the infrared sensor on the unit by using the following procedure. 1. Hold down the 3 cursor button and the MENU button on the front panel at the same time for five seconds. 2. The setting "ENABLE" is shown on the FL DISPLAY. 3. Press the CURSOR buttons (1, 2) to change this to "DISABLE". 4. Press the ENTER button. Once this setting is made, the infrared sensor on the unit is disabled. Note • Be sure to set to "ENABLE" when external infrared sensors or similar devices are not connected. Otherwise, the unit will be unable to receive remote control commands. 5. To restore the original setting, perform steps 1 to 4 to set to "ENABLE". BASIC OPERATION ADVANCED CONNECTIONS SETUP ADVANCED OPERATION TROUBLESHOOTING OTHERS 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
NAMES AND
FUNCTIONS
16
BASIC
CONNECTIONS
BASIC
OPERATION
ADVANCED
CONNECTIONS
SETUP
ADVANCED
OPERATION
TROUBLESHOOTING
OTHERS
ADVANCED
CONNECTIONS
ENGLISH
ADVANCED CONNECTIONS
CONNECTING THE REMOTE CONTROL JACKS
IN
IN
OUT
OUT
PRE OUT
PRE OUT
GAME
GAME
DVD
DVD
DSS
DSS
L
R
DIGITAL
DIGITAL
AUDIO
AUDIO
IN
IN
SURROUND BACK
SURROUND BACK
R
L
3
2
1
GND
GND
AM
AM
AC IN
AC IN
MODEL NO. NR1501
MODEL NO. NR1501
VIDEO
VIDEO
FM
FM
(
75
75
Ω
)
SPEAKER SYSTEMS : 6-8 OHMS
SPEAKER SYSTEMS : 6-8 OHMS
COMPONENT VIDEO
COMPONENT VIDEO
DVD
DVD
MONITOR OUT
MONITOR OUT
OUT
OUT
MONITOR OUT
MONITOR OUT
IN
IN
IN
IN
IN
IN
IN
IN
IN
IN
OUT
OUT
SUB
SUB
DVD
DVD
DSS
DSS
VCR
VCR
CD
CD
AUX 2
AUX 2
WOOFER
WOOFER
ANTENNA
ANTENNA
REMOTE CONTROL
REMOTE CONTROL
ANALOG AUDIO
ANALOG AUDIO
DSS
DSS
VCR
VCR
IN
IN
IN
IN
DVD
DVD
DSS
DSS
IN
IN
VCR
VCR
P
R
/
C
R
P
R
/
C
R
P
B
/
C
B
P
B
/
C
B
Y
Y
OUT
OUT
BLU-RAY
BLU-RAY
CENTER
CENTER
R
-
SURR.
SURR.
-
L
R
-
FRONT
FRONT
-
L
IN
IN
OUT
OUT
REMOTE CONTROL
REMOTE CONTROL
REMOTE
CONTROL
REMOTE
CONTROL
REMOTE
CONTROL
IN
OUT
IN
OUT
IN
OUT
EXTERNAL INTERNAL
EXTERNAL INTERNAL
EXTERNAL INTERNAL
1
RC OUT
2
Option
DVD player
CD player
CD recorder
q
You can control other Marantz products through this
unit with the remote controller by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote controller
is received by the remote sensor on this unit. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the remote
control only at the unit. Also, if a Marantz power
amplifier (some models excluded) is connected
to one of these terminals, the power amplifier’s,
power switch is synchronized with this unit’s power
switch.
Set the REMOTE CONTROL SWITCH on the back of
other units (not the NR1501) to “EXT.” (EXTERNAL)
to use this feature.
w
Whenever external infrared sensors or similar
devices are connected to RC-5 IN of the unit, be sure
to always disable operation of the infrared sensor on
the unit by using the following procedure.
1.
Hold down the
3
cursor button and the
MENU
button on the front panel at the
same time for five seconds.
2.
The setting “ENABLE” is shown on the FL
DISPLAY.
3.
Press the
CURSOR
buttons (
1
,
2
) to change
this to “DISABLE”.
4.
Press the
ENTER
button. Once this setting
is made, the infrared sensor on the unit is
disabled.
Note
• Be sure to set to “ENABLE” when external
infrared sensors or similar devices are not
connected. Otherwise, the unit will be unable to
receive remote control commands.
5.
To restore the original setting, perform
steps 1 to 4 to set to “ENABLE”.