Marantz NR1501 NR1501 User Manual - English - Page 34

Tuner Operations, Preset Memory

Get Marantz NR1501 PDF manuals and user guides View all Marantz NR1501 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

ENGLISH NAMES AND FUNCTIONS CONNECTIONS BASIC OPERATION ADVANCED CONNECTIONS BASIC ADVANCED OPERATION TUNER OPERATIONS (PRESET MEMORY) With this unit, up to 30 FM and AM broadcast stations can be preset in the sequence desired. For each of these stations, the frequency and reception mode can be stored in the memory as needed. AUTO PRESET MEMORY This function makes it possible to scan the FM band automatically and store all stations with suitable signal strength in the unit's preset memories. 1. 2. 1. 2. MANUAL PRESET MEMORY (When performing the operations using the unit's controls) 3. 2. 4. 1. Tune into the frequency of the broadcast station to be set. (Refer to the section on "MANUAL TUNING" or "AUTO TUNING".) 2. Press the unit's MEMORY button. The MEM indicator starts blinking on the display. 2. Press the EXIT/MEMO button on the remote controller. The MEM indicator starts blinking on the display. 3. While the MEM indicator is still blinking, press the 1/2 cursor buttons to select the preset number. 4. Press the EXIT/MEMO button again to enter the selection. CALLING PRESET STATIONS 1. 1. 2. 1. Hold down the unit's MEMORY button or the EXIT/MEMO button on the remote controller for at least two seconds. "AUTO MEM" appears on the display, and scanning starts from the lowest frequency. 2. Scanning automatically stops when all 30 preset memories have been set or when auto scanning has reached the uppermost limit of the band. To stop the auto preset memory operation at any time, press the unit's MEMORY button or the EXIT/MEMO button on the remote controller. Note The auto preset cannot be performed for AM stations. Perform the manual preset instead. 30 3. While the MEM indicator is still blinking, press the 1/2 cursor buttons to select the preset number. 4. Press the MEMORY button again to enter the selection. The indicator stops blinking, and the broadcast station is stored in the preset memory selected. (When performing the operations using the remote controller) 3. 2. 4. 1. Tune into the frequency of the broadcast station to be set. (Refer to the section on "MANUAL TUNING" or "AUTO TUNING".) 2. (When performing the operations using the unit's controls) 1. Press the unit's 1/2 cursor buttons to select the preset station to be called. (When performing the operations using the remote controller) 1. Press the TUNE button on the remote controller twice in succession. 2. Press the 1/2 cursor buttons to select the preset station whose programs are to be heard. Alternatively, press the numeric buttons to select the preset station. SETUP ADVANCED OPERATION TROUBLESHOOTING OTHERS

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
NAMES AND
FUNCTIONS
30
BASIC
CONNECTIONS
BASIC
OPERATION
ADVANCED
CONNECTIONS
SETUP
ADVANCED
OPERATION
TROUBLESHOOTING
OTHERS
ADVANCED
OPERATION
ENGLISH
ADVANCED OPERATION
TUNER OPERATIONS
(PRESET MEMORY)
With this unit, up to 30 FM and AM broadcast
stations can be preset in the sequence desired.
For each of these stations, the frequency and
reception mode can be stored in the memory as
needed.
AUTO PRESET MEMORY
This function makes it possible to scan the FM band
automatically and store all stations with suitable
signal strength in the unit's preset memories.
1. 2.
1.
2.
1.
Hold down the unit's
MEMORY
button
or the
EXIT/MEMO
button on the remote
controller for at least two seconds.
“AUTO MEM” appears on the display, and
scanning starts from the lowest frequency.
2.
Scanning automatically stops when all 30
preset memories have been set or when
auto scanning has reached the uppermost
limit of the band.
To stop the auto preset memory operation
at any time, press the unit's
MEMORY
button or the
EXIT/MEMO
button on the
remote controller.
Note
The auto preset cannot be performed for AM
stations. Perform the manual preset instead.
MANUAL PRESET MEMORY
(When performing the operations using the
unit's controls)
2. 4.
3.
1.
Tune into the frequency of the broadcast
station to be set.
(Refer to the section on “MANUAL
TUNING” or “AUTO TUNING”.)
2.
Press the unit’s
MEMORY
button. The MEM
indicator starts blinking on the display.
3.
While the MEM indicator is still blinking,
press the
1
/
2
cursor buttons to select the
preset number.
4.
Press the
MEMORY
button again to enter
the selection.
The indicator stops blinking, and the
broadcast station is stored in the preset
memory selected.
(When performing the operations using the
remote controller)
2.
4.
3.
1.
Tune into the frequency of the broadcast
station to be set.
(Refer to the section on “MANUAL
TUNING” or “AUTO TUNING”.)
2.
Press the
EXIT/MEMO
button on the
remote controller. The MEM indicator starts
blinking on the display.
3.
While the MEM indicator is still blinking,
press the
1
/
2
cursor buttons to select the
preset number.
4.
Press the
EXIT/MEMO
button again to
enter the selection.
CALLING PRESET STATIONS
1.
1.
2.
2.
(When performing the operations using the
unit's controls)
1.
Press the unit’s
1
/
2
cursor buttons to select
the preset station to be called.
(When performing the operations using the
remote controller)
1.
Press the
TUNE
button on the remote
controller twice in succession.
2.
Press the
1
/
2
cursor buttons to select the
preset station whose programs are to be
heard.
Alternatively, press the numeric buttons to
select the preset station.