Marantz SR7001 User Manual - Page 20

ENGLISH ADVANCED CONNECTING CONNECTING THE REMOTE CONTROL JACKS DVD Audio player or Super Audio CD Multi channel player CENTER L R L FRONT SURR. SURR. SUB R BACK WOOFER RL RL RL RL RLRL UT 1(TV) INPUT 2(DVD) OUT PUT 1 MODEL NO RL RL RL CB/PB CR/PR UT 3(VCR1) T 4(DSS/VCR2) Y CB/PB CR/PR Y INPUT 4(DSS/VCR2) OUTPUT 1 OUTPUT 2 CB/PB CR/PR OUT PUT 2 HDMI Ver1.2 MULTI OUT TV(1) DVD(2) VCR1(3) DSS/VCR2(4) MONI. OUT RS-232C XM N UT E DC OUT IN OUT IN L 1 1 IR FLASHER RECEIVER IN IN 2 2 CD/CDR EMITTER OUT R MULTI OUT L OUT SL S-VIDEO SBL C PRE OUT SR SBR SW SL SBL C 7.1CH IN L AC R FRONT SURR. SURR. BACK Power Amplifer Subwoofer CENTER SUB WOOFER OUT IN OUT A O B R SR (AUX2) SBR SW LR LRLR Front Center Front Left Right Surround Left Surround Right INPUT 1(TV) INPUT 2(DVD) OU PU 1 FM (75Ω) GND AM ANTENNA INPUT 1(TV) COMPONENT VIDEO Y CB/PB CR/PR INPUT 3(VCR1) INPUT 2(DVD) INPUT 3(VCR1) INPUT 4(DSS/VCR2) Y CB/PB CR/PR Y INPUT 4(DSS/VCR2) OUTPUT 1 OUTPUT 2 CB/PB CR/PR OU PU 2 HDMI Ver1.2 TV(1) DVD(2) VCR1(3) DSS/VCR2(4) MONITOR MULTI OUT OUT TV(1) DVD(2) VCR1(3) DSS/VCR2(4) MONI. OUT VIDEO IN DIGITAL IN OUT IN DIGITAL OUT OUT RC-5 MULTI RC DC OUT 2 IN OUT IN OUT S-VID L SL SBL 4 5 6 1 2 3 TV DVD VCR1 COAX. OPT. DSS/VCR2 IN OUT TAPE 1 1 IR FLASHER RECEIVER IN IN 2 2 CD/CDR EMITTER OUT R MULTI OUT L SR SBR S SL SBL L R IN OUT IN OUT IN OUT IN OUT A AUDIO B R SR SBR S (AUX2) REMOTE CONTROL IN OUT 1 CD recorder EXTERNAL INTERNAL REMOTE CONTROL IN OUT DVD player EXTERNAL INTERNAL RC OUT OPTION REMOTE CONTROL IN OUT CD player EXTERNAL INTERNAL CONNECTING MULTI CHANNEL AUDIO SOURCE The 7.1CH INPUT jacks are for multichannel audio source such as a Super Audio CD multichannel player, DVD audio player or external decoder. If you use these jacks, switch on the 7.1CH INPUT and set the 7.1CH INPUT level by using the SETUP MAIN MENU. See page25. Surround Back Left Surround Back Right CONNECTING AN EXTERNAL POWER AMPLIFIER The PREOUT jacks are for connecting external power amplifiers. Be sure to connect each speaker to the corresponding external power amplifier. q You can control other Marantz products through the SR7001 with the remote control by connecting the REMOTE CONTROL terminals on each unit. The signal transmitted from the remote control is received by the remote sensor on the SR7001. Then the signal is sent to the connected device through this terminal. Therefore you need to aim the remote control only at the SR7001. Also, if a Marantz power amplifier (some models excluded) is connected to one of these terminals, the power amplifier's, power switch is synchronized with this unit's power switch. Set the REMOTE CONTROL SWITCH on the other units, (not the SR7001) to "EXT." (external) to use this feature. w Whenever external infrared sensors or similar devices are connected to RC-5 IN of the SR7001, be sure to always disable operation of the infrared sensor on the main unit by using the following procedure. 1. Hold down the MULTI button and the MENU button on the front panel at the same time for five seconds. 2. The setting "IR=ENABLE" is shown on the FL DISPLAY. 3. Press the CURSOR buttons (1, 2) to change this to "IR=DISABLE". 4. Press the ENTER button. Once this setting is made, the infrared sensor on the main unit is disabled. Note: • Be sure to set to "IR=ENABLE" when external infrared sensors or similar devices are not connected. Otherwise, the main unit will be unable to receive remote control commands. 5. To restore the original setting, perform steps 1 to 4 to set to "IR=ENABLE". 17