Marantz SR7001 User Manual - Page 49

Other Function - phono

Page 49 highlights

ENGLISH OTHER FUNCTION TV AUTO ON/OFF FUNCTION This function allows the component connected to the TV-VIDEO in jack to control the power (ON/OFF) to the SR7001. AUTO POWER ON 1. Be sure the TV auto mode is ENABLED. (Refer to page 35: PREFERENCE) 2. Connect your TV TUNER (etc) to the TV- VIDEO in terminal. Be sure to connect the VIDEO input. 3. Turn OFF the power to the TV TUNER and the SR7001. 4. Turn ON the TV TUNER and tune in a receivable station. 5. When the station is received, the SR7001 turns ON and TV is selected automatically. AUTO POWER OFF 1. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast. 2. The power to the SR7001 switches to STANDBY after approx. 5 minutes. Notes: • AUTO POWER OFF is canceled if the SR7001 is set to a source other than TV. The function reactivates when TV is selected again. • Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON. • The S-Video terminal does not support "TV AUTO ON/OFF" function. ATTENUATION TO ANALOG INPUT SIGNAL PREV MENU TEST 1 7.1CH 4 DISP 7 CLEAR LIP.SYNC GUIDE CH.SEL 2 ATT 5 OSD 8 THX 0 MUTE EXIT SURR 3 SPK-AB 6 SLEEP 9 MEMO If the selected analog audio input signal is greater than the capable level of internal processing, the "PEAK" indicator will light up on the front display. If this happens, you should press the ATT button on the remote. "ATT" indicator will be illuminated when this function is activated. The signal-input level is reduced by about half. Attenuation will not work with the output signal of TAPE-OUT, CD/CD-R, VCR1-OUT and DSS/VCR2-OUT. This function is memorized for each individual input source. LISTENING THROUGH HEADPHONES This jack may be used to listen to the SR7001's output through a pair of headphones. Be certain that the headphones have a standard 1/4" stereo phono plug. (Note that the speakers will automatically be turned off when the headphone jack is in use.) AV SURROUND RECEIVER SR8001 INPUT SELECTOR PURE DIRECT DSD DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST SP DISC 6.1 STANDBY POWER ON/STANDBY PHONES SURROUND MODE AUTO MULTI MULTI SPEAKER PURE DIRECT THX 7.1CH INPUT MENU Note: • The surround mode returns to the previous setting as soon as the plug is removed from the jack. DOLBY HEADPHONE MODE This feature simulates the waveforms of the actual sounds heard from the speakers. When headphones are used, the MENU button automatically switches to the Dolby headphone mode. The OSD that appears when the MENU button is pressed is shown below. HEAD PHONE DOLBY HP MODE : DH SURROUND : P L II CINEMA L LEVEL R LEVEL : +10dB : 0dB DOLBY HP (Headphone) MODE can be selected with the left and right cursor buttons. BYPASS → DH (DOLBY Headphone) → BYPASS BYPASS: Bypasses the Dolby headphone mode and delivers ordinary 2-channel stereo. DH: Dolby Headphone is a signal processing system that delivers a sound similar to room speakers. It makes it possible to experience the volume and space of a 5-channel surround system using ordinary stereo headphones. When the PURE DIRECT mode is selected, Dolby surround processing is bypassed and is displayed as the mode indication. The surround mode can be selected when the modes in DH is selected. L/R LEVEL can be set in the ±12 dB range. Notes: • The surround mode returns to the previous setting as soon as the plug is removed from the jack. • TONE cannot be set when the mode in DH is selected. • The Dolby Headphone function will not work when 32 or 96 kHz PCM digital signals are input. VIDEO ON/OFF When no video signal is connected to the SR7001 or a DVD, etc., is connected directly to your TV, the unnecessary video circuit can be turned off by selecting the "VIDEO OFF" setting. To select video off, press the AMP button and press the > button until PAGE 4 is displayed. Press the V-OFF button. UND RECEIVER SR8001 ONES PURE DIRECT DSD DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST SPKR A B V-OFF PEAK ATT DISC 6.1 MTX 6.1 NIGHT EQ ANALOG DIGITAL AAC PCM SURROUND DIGITAL LCR LFE SL S SR SURROUND MODE AUTO MULTI MULTI SPEAKER BAND T-MODE MEMORY CLEAR PURE DIRECT THX 7.1CH INPUT MENU ENTER DISPLAY EXIT MultEQ SPEAKERS A/B MIC USE PAGE 4 M D1 D2 D3 D4 D5 CH VOL TUNER CD CD-R MD TAPE 1 AUX1 AUX2 LIGHT RC8001SR Learning Remote Controller AMP 2 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79

46
ENGLISH
OTHER FUNCTION
TV AUTO ON/OFF FUNCTION
This function allows the component connected to the
TV-VIDEO in jack to control the power (ON/OFF) to
the SR7001.
AUTO POWER ON
1.
Be sure the TV auto mode is ENABLED. (Refer
to page 35: PREFERENCE)
2.
Connect your TV TUNER (etc) to the TV-
VIDEO in terminal. Be sure to connect the
VIDEO input.
3.
Turn OFF the power to the TV TUNER and the
SR7001.
4.
Turn ON the TV TUNER and tune in a receivable
station.
5.
When the station is received, the SR7001 turns
ON and TV is selected automatically.
AUTO POWER OFF
1.
In the above situation, turn the TV TUNER OFF
or select a channel that does not contain any
broadcast.
2.
The power to the SR7001 switches to STANDBY
after approx. 5 minutes.
Notes:
• AUTO POWER OFF is canceled if the SR7001 is
set to a source other than TV.
The function reactivates when TV is selected again.
• Some TV broadcasts may cause the TV AUTO
FUNCTION to turn ON.
• The S-Video terminal does not support “TV AUTO
ON/OFF” function.
ATTENUATION TO ANALOG INPUT SIGNAL
2
3
1
5
6
4
8
0
9
7
MEMO
CLEAR
PREV
MUTE
MENU
EXIT
GUIDE
TEST
CH.SEL
LIP.SYNC
SURR
7.1CH
ATT
SPK-AB
DISP
OSD
THX
SLEEP
5
ATT
If the selected analog audio input signal is greater
than the capable level of internal processing, the
PEAK
” indicator will light up on the front display.
If
this happens, you should press the
ATT
button
on
the remote.
ATT
” indicator will be illuminated when this function
is activated. The signal-input level is reduced by
about half. Attenuation will not work with the output
signal of TAPE-OUT, CD/CD-R, VCR1-OUT and
DSS/VCR2-OUT.
This function is memorized for each individual input
source.
LISTENING THROUGH HEADPHONES
This jack may be used to listen to the SR7001’s
output through a pair of headphones. Be certain that
the headphones have a standard 1/4” stereo phono
plug. (Note that the speakers will automatically be
turned off when the headphone jack is in use.)
AV SURROUND RECEIVER SR8001
Note:
• The surround mode returns to the previous setting as
soon as the plug is removed from the jack.
DOLBY HEADPHONE MODE
This feature simulates the waveforms of the actual
sounds heard from the speakers.
When headphones are used, the
MENU
button
automatically switches to the Dolby headphone
mode.
The OSD that appears when the
MENU
button is
pressed is shown below.
HEAD PHONE
DOLBY HP MODE : DH
SURROUND
: PL
II
CINEMA
L LEVEL
: +10dB
R LEVEL
:
0dB
DOLBY HP (Headphone) MODE can be selected
with the left and right cursor buttons.
BYPASS
DH (DOLBY Headphone)
BYPASS
BYPASS: Bypasses the Dolby headphone mode
and delivers ordinary 2-channel stereo.
DH: Dolby Headphone is a signal processing
system that delivers a sound similar to
room speakers.
It makes it possible to experience
the volume and space of a 5-channel
surround system using ordinary stereo
headphones.
When the PURE DIRECT mode is selected, Dolby
surround processing is bypassed and “
✽✽✽
” is
displayed as the mode indication.
The surround mode can be selected when the
modes in DH is selected.
L/R LEVEL can be set in the ±12 dB range.
Notes:
• The surround mode returns to the previous setting as
soon as the plug is removed from the jack.
• TONE cannot be set when the mode in DH is
selected.
• The Dolby Headphone function will not work when
32 or 96 kHz PCM digital signals are input.
VIDEO ON/OFF
When no video signal is connected to the SR7001
or a DVD, etc., is connected directly to your TV,
the unnecessary video circuit can be turned off by
selecting the “
VIDEO OFF
” setting.
To select video off, press the
AMP
button and press
the
>
button until PAGE 4 is displayed. Press the
V-OFF
button.
UND RECEIVER SR8001
DIGITAL
SURROUND
AAC
AMP
AUX2
AUX1
TAPE
TUNER
CD
CD-R
MD
1
2
LIGHT
Learning Remote Controller
RC8001SR
AMP
D4
D5
D2
M
D1
D3
D5
VOL
CH
USE
PAGE
4
D4