Marantz SR7300OSE User Guide - Page 15

ENGLISH ⁄5 CURSOR / OK button Used to operate on-screen and other displays used by receivers and other components. ⁄6 CH SEL. (channel select) button (when AMP mode is selected) Used to call up SETUP MAIN MENU and adjust speaker levels or 7.1 ch input level. ⁄7 SETUP button (when AMP mode is selected) Used to call up the SETUP MAIN MENU of the SR7300. ⁄8 CONTROL buttons These buttons are used when operating the CD player, TAPE deck, etc. The function of these buttons are dependent on the function button selected. (when AMP mode is selected) ATT button When the input signal is too high and the voice distorts even by throttling the SR7300 VOLUME control, turn on this function. "ATT" is indicated when this function is activated. The input level is reduced. Attenuator is invalid for use with the output signal of "REC OUT". Note: • This function is unavailable during the digital input is selected. SPKR A/B button Speaker mode is switched in the following sequence. A → B → A+B → off MULTI button This button is used to switch the unit to multi room mode. ⁄9 Input selector buttons/ FUNCTION SELECTOR buttons (AUDIO/VIDEO INPUT) Used to switch the remote controller to the command sets for specific sources (amplifier, receiver, etc.), thereby allowing a single remote controller to control up to 11 different components. To use these buttons to switch the amplifier's source, press the desired button twice within 2 seconds. The AMP button is used only to switch command set of the remote controller itself and therefore does not transmit any signal. Further, the function buttons may also be programmed to execute macros. (A macro allows a complex string of operations to be performed in series simply by pressing a single button.) One button can be programmed to learn sequences containing up to 10 commands. The following is an example of such a sequence that can be activated automatically using a macro: Turn the receiver ON → Switch the function to DVD → Set the Surround Mode to VIRTUAL → Set the DVD player to Play. ¤0 EXIT button (when AMP mode is selected) Used to exit setup menu. ¤1 TEST button (when AMP mode is selected) Used to enter the test tone menu. ¤2 MENU/OSD button (when AMP mode is selected) When this button is pressed, the current setting are displayed on the TV monitor. ¤3 VOLUME / buttons Used to adjust the volume on receivers and other components (TV) equipped with volume control. ¤4 P.SCAN (preset scan) button (when TUNER mode is selected) Used to start preset scan when SR7300 is selected TUNER mode. ¤5 MUTE button Muting button of the SR7300. Press this button decrease the sound temporarily . Press this button again to return to the previous sound. ¤6 MEMO button Memory enable button for various preset functions. ¤7 NIGHT button (when AMP mode is selected) Pressing this button prevents the Dolby Digital signal from playback at a loud voice. This function reduces the voice by 1/3 to 1/4 at maximum. Thus, it eliminates the occurrence of an abruptly loud voice at night. However, the function is valid only for the case when the Dolby Digital signal is entered into OPTICAL or COAXIAL and data to compress the voice exists in the signal to be played back. When this button is pressed, "NIGHT" indicator lights up. ¤8 PTY button (European model only) (when TUNER mode is selected) Used to display the programme type information of the current station. The RDS system categorizes programmes according to their genre into different programme type (PTY) groups. ¤9 F.DIR/SEAR button (when TUNER mode is selected) Used to select the mode of frequency direct input. ‹0 DISP./RDS button (when TUNER mode is selected: European model only) Selects display mode function in RDS (Radio Data System) by this button. (when AMP mode is selected) Selects the display mode for the front display of the SR7300. ‹1 A/D button This is used to switch between the analog and digital inputs. ‹2 SLEEP (sleep timer) button This button is used for setting the sleep timer. It can be operated the same way as the button in unit. ‹3 7.1/6.1CH IN button Press this button to select the output of an external multi channel decoder. ‹4 POWER ON, OFF buttons (when AMP mode is selected) Press to switch the power of the SR7300 ON or OFF. 11