Marantz SR7300OSE User Guide - Page 36

ENGLISH OTHER FUNCTION TV AUTO ON/OFF FUNCTION This function allows the component connected to the TV-VIDEO in jack to control the power (ON/OFF) to the SR7300. AUTO POWER ON 1. Be sure TV auto mode is ENABLE. (Refer page 24 : System Setup) 2. Connect your TV TUNER (etc) to the TV-VIDEO in terminal. Be sure to connect the VIDEO input. 3. Turn OFF the power to the TV TUNER and the SR7300. 4. Turn ON the TV TUNER and tune in a receivable station. 5. When the station is received, the SR7300 turns ON and TV is selected automatically. AUTO POWER OFF 1. In the above situation, turn the TV TUNER OFF or select a channel that does not contain any broadcast. 2. The power to the SR7300 switches to STANDBY after approx. 5 minutes. Notes: • AUTO POWER OFF is canceled if the SR7300 is set to a source other than TV. The function reactivates when TV is selected again. • Some TV broadcasts may cause the TV AUTO FUNCTION to turn ON. • S-Video terminal does not support "TV AUTO ON/OFF" function. ATTENUATION TO ANALOG INPUT SIGNAL VOLUME CLEAR MEMORY TUNING F/P MODE SPEAKRS A/B 7.1CH INPUT A/D S-DIRECT MULTIROOM TV DVD VCR1 DSS/VCR2 AUX1 AUX2 CD-R TAPE CD TUNER DOWN UP MUTE ATT DIGITAL S-VIDEO AUX1 INPUT VIDEO L AUDIO R If the selected analog audio input signal is greater than the capable level of internal processing, "PEAK" indicator will light up on the front display. If this happens, you should press the ATT button on the front panel or on the remote. "ATT" indicator will light up when this function is activated. The signalinput level is reduced by about the half. Attenuation will not work with the output signal of TAPE-OUT, CD-R/MD-OUT, VCR1-OUT, VCR2OUT and MULTI ROOM OUT. This function is memorized for each individual input source. LISTENING OVER HEADPHONES This jack may be used to listen to the SR7300's output through a pair of headphones. Be certain that the headphones have a standard 1/4" stereo phone plug. (Note that the main room speakers will automatically be turned off when the headphone jack is in use.) SURROUND SELECT STANDBY POWER ON/STANDBY ENTER PHONES CLEAR MEMORY TUNING SPEAKRS A/B 7.1CH INPUT A/D TV DVD VCR1 DSS/VCR2 AUX1 Notes: • When using headphones, the surround mode will automatically change to STEREO. • The surround mode returns to the previous setting as soon as the plug is removed from the jack. 32 VIDEO ON/OFF When no video signals of a DVD, etc., are connected to the SR7300 or the DVD, etc., are connected directly to a TV, the unnecessary video circuit can be turned off by selecting the "VIDEO OFF" setting. To select video off condition, press the V-OFF on the remote. Notes that VIDEO OFF will not work with the output signal of MULTI ROOM OUT. SURROUND AV SURROUND RECEIVER SR7300 CLEAR DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST V - OFF NIGHT PEAK ATT DISC 6.1 MTX 6.1 SPKR AB EQ ANALOG DIGITAL PCM SURROUND DIGITAL LCR LFE SL S SR MEMORY TUNING F/P MODE SELECT STANDBY POWER ON/STANDBY ENTER PHONES SPEAKRS A/B 7.1CH INPUT A/D S-DIRECT MULTIROOM TV DVD VCR1 DSS/VCR2 AUX1 AUX2 CD-R TAPE CD TUNER DISPLAY MODE SURROUND AV SURROUND RECEIVER SR7300 CLEAR DISP MULTI AUTO TUNED SLEEP AUTO SURR DIRECT ST V - OFF NIGHT PEAK ATT DISC 6.1 MTX 6.1 SPKR AB EQ ANALOG DIGITAL PCM SURROUND DIGITAL LCR LFE SL S SR MEMORY TUNING F/P MODE SELECT STANDBY POWER ON/STANDBY ENTER PHONES SPEAKRS A/B 7.1CH INPUT A/D S-DIRECT MULTIROOM TV DVD VCR1 DSS/VCR2 AUX1 AUX2 CD-R TAPE CD TUNER You can select the display mode for the front display of the SR7300. To select this mode, press the DISP. on the remote control unit. When this button is pressed, the display mode is switched in the following sequence. → Surround Mode → Auto-display Off → Display Off → Input Function → Surround Mode.... In Auto display off mode, turn the display on automatically, after that any condition of SR7300 is changed. In Display off mode, turn the display off completely. Notes: • Only DISP indicator will light up on the front display in display off condition SELECTING ANALOG AUDIO INPUT OR DIGITAL AUDIO INPUT SURROUND AV SURROUND RECEIVER SR7300 SELECT STANDBY POWER ON/STANDBY ENTER PHONES CLEAR MEMORY TUNING F/P MODE SPEAKRS A/B 7.1CH INPUT A/D S-DIRECT MULTIROOM TV DVD VCR1 DSS/VCR2 AUX1 AUX2 CD-R TAPE CD TUNER If you have already assign any digital input to input source. You can select temporarily the audio input mode for each input source with the A/D button on the remote controller or front panel. When this button is pressed, the input mode is switched in the following sequence. → Digital Auto → Digital → Analog → Digital Auto.... In Digital Auto mode, the types of signals being input to the digital and analog input jacks for the selected input source are detected automatically. If no digital signal is being input, the analog input jacks are selected automatically. In Digital mode, input is fixed to an assigned digital input terminal. In analog mode, the analog input jacks are selected. This selecting is temporarily, so the result will not be stored in memory. If you need to change input mode completely, use SYSTEM SETUP in OSD menu system. (see page 22)