Marantz SR7300OSE User Guide - Page 40

ENGLISH 3. Each time the tuner finds a station, scanning will pause and the station will be played for five seconds. During this time, the following operations are possible. 1) The band can be changed by TUNER button . 2) The tuning mode can be changed by MODE button. 4. If no button is pressed during this period, the current station is memorized in location Preset 02 If you wish to skip the current station, press the TUNING button during this period, this station is skipped and auto presetting continues. 5. Operation stops automatically when all 50 preset memory positions are filled or when auto scanning attains the highest end of all bands. If you desire to stop the auto preset memory at anytime, press the CLEAR button. MANUAL PRESET MEMORY 2. 4. 3. SURROUND AV SURROUND RECEIVER SR7300 CLEAR MEMORY TUNING 3. F/P M SELECT STANDBY POWER ON/STANDBY ENTER PHONES SPEAKRS A/B 7.1CH INPUT A/D S-DIRECT MU TV DVD VCR1 DSS/VCR2 AUX1 AUX2 CD-R TAPE CD 2. (Using the SR7300) 1. Tune into the radio station you desire (Refer to the "MANUAL TUNING" or "AUTO TUNING" section). 2. Press the MEMORY button on the front panel. "- -" (preset number) starts blinking on the display. 3. Select the preset number by pressing the TUNING or button, while this is still blinking (approx. 5 seconds) 4. Press the MEMORY button again to enter. The display stops blinking. The station is now stored in the specified preset memory location. (Using the remote control unit) 1. Tune into the radio station you desire (Refer to the "MANUAL TUNING" or "AUTO TUNING" section). 2. Press the MEMO on the remote unite. "- -" (preset number) starts blinking on the display. 3. Enter the desired preset number by pressing numeric buttons. Note: • When entering a single digit number (2 for example), either input "02" or just input "2" and wait for a few seconds. RECALLING A PRESET STATION 2. 1. CLEAR MEMORY SPEAKRS A/B 7.1CH INPUT TUNING A/D F/P S-DIRECT MODE MULTIROOM 1. TV DVD VCR1 DSS/VCR2 AUX1 AUX2 CD-R TAPE CD TUNER 1. PRESET SCAN 3. 1. 3. (Using the remote control unit) 1. Press the P.SCAN on remote. "PRESET SCAN" appears on the display and then the preset station with the lowest preset number is recalled first. 2. Preset stations are recalled in sequence (No.1 → No.2 → etc.) for 5 seconds each. No stored preset number will be skipped. 3. You can fast forward the preset stations by pressing the ¢ continuously. When the desired preset station is received, cancel the preset scan operation by pressing the CL button or P.SCAN on the remote. CLEARING STORED PRESET STATIONS You can remove preset stations from memory using the following procedure. 2. 3. SURROUND AV SURROUND RECEIVER SR7300 SELECT STANDBY POWER ON/STANDBY ENTER PHONES CLEAR MEMORY SPEAKRS A/B 7.1CH INPUT TUNING A/D 3. F/P M S-DIRECT 2. MU TV DVD VCR1 DSS/VCR2 AUX1 AUX2 CD-R TAPE CD 1. Recall the preset number to be cleared with the method described in "Recalling" a preset station. 2. Press the MEMORY button on the front panel or press MEMO button on the remote. 3. Stored preset number blinks in the display for 5 seconds. While blinking, press the CLEAR button on the front panel or press CL button on the remote. 4. "xx CLEAR" appears on the display to indicate that the specified preset number has been cleared. Notes: • To clear stored all preset stations, press and hold the CLEAR and the F/P buttons for two seconds. (Using the SR7300) 1. Press the F/P button to show the preset station on the display. 2. Select the desired preset station by pressing the TUNING or button on the front panel (Using the remote control unit) 1. Press the 4 or ¢ button to select the desired preset station, or input your desired preset channel with numeric buttons on the remote. 36