Oki C3600n C3600n User Guide (English) - Page 94

locating the two lugs into their slots in the metal partition which, Holding the fuser handle 2

Get Oki C3600n PDF manuals and user guides View all Oki C3600n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

3. Holding the fuser by its handle (1), lift the fuser straight up and out of the printer. If the fuser is still warm, place it on a flat surface which will not be damaged by heat. 4. Remove the new fuser from its packaging and remove the transit material. 5. Holding the new fuser by its handle, make sure that it is the correct way round. The retaining levers (2) should be fully upright, and the locating lugs (3) should be towards you. There is one locating lug at each end of the fuser. Fuser Alone.jpg 3 2 2 6. Holding the fuser handle (2), lower the fuser into the printer, locating the two lugs into their slots in the metal partition which separates the fuser area from the image drums. fuser going in_F8_12.jpg 7. Push the two retaining levers (1) towards the rear of the printer to lock the fuser in place. 8. Finally, close the top cover and press down firmly at both sides so that the cover latches closed. C3600n User's Guide 94

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
C3600n User’s Guide
94
3.
Holding the fuser by its handle (1), lift the fuser straight up and
out of the printer. If the fuser is still warm, place it on a flat
surface which will not be damaged by heat.
4.
Remove the new fuser from its packaging and remove the transit
material.
5.
Holding the new fuser by its handle, make sure that it is the
correct way round. The retaining levers (2) should be fully
upright, and the locating lugs (3) should be towards you. There is
one locating lug at each end of the fuser.
Fuser Alone.jpg
6.
Holding the fuser handle (2), lower the fuser into the printer,
locating the two lugs into their slots in the metal partition which
separates the fuser area from the image drums.
fuser going
in_F8_12.jpg
7.
Push the two retaining levers (1) towards the rear of the printer
to lock the fuser in place.
8.
Finally, close the top cover and press down firmly at both sides so
that the cover latches closed.
2
3
2