Panasonic AW-HN40H AW-HN38H Operating Instructions - Page 48

Others 3/4 screen

Get Panasonic AW-HN40H PDF manuals and user guides View all Panasonic AW-HN40H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Camera menu items (continued) IR Control [Disable, Enable] "Enable" or "Disable" is set here for operations conducted from the wireless remote control. The operations are enabled when the unit's power is turned on from an external device other than a wireless remote control, and they are disabled when the power is turned on from a wireless remote control. Notes ●● At the point when this item's setting is changed, the new setting is not reflected in operation. It is reflected when the unit is set to standby mode and its power is turned on. ●● Follow one of the procedures below if the item's setting is changed by mistake and the unit can no longer be operated from a wireless remote control. When menu operations can be performed using another control device:  First change the item using a control device capable of performing menu operations, and then turn off the unit's power and turn it back on. When menu operations cannot be performed using other control devices: 1. Turn off the power of the units and devices that are connected. 2. Disconnect the unit's AC adaptor cable and LAN cable, and plug them back in. 3. Perform the operation for turning on the unit's power from the wireless remote control. 4. After changing this item, turn off the unit's power and turn it back on. IR ID [CAM1, CAM2, CAM3, CAM4] Configure the unit's remote control ID. The settings for this item correspond to the [CAM1] to [CAM4] buttons on the wireless remote control. Return Use this to return to the previous menu. ■■Others 3/4 screen ### Others 3/4 ### CAM/BAR Bars Type OSD Off With Tally OSD Status Camera Type2 Off Off Return CAM/BAR [Camera, Colorbar] Switch between color bar display and camera image display on the monitor and the web setup screen. Note ●● When the color bar is displayed, a test tone (1 kHz) is output according to the Audio setting in the camera menu. Bars Type [Type1, Type2] Change the type of color bar to display. Type1: , Type2: OSD Off With Tally [Off, On] This is used to enable or disable the function for clearing the OSD menu displays when the tally signal is received by a command or contact. When the tally signal is released, the original OSD menu displays are restored. OSD Status [Off, On] "Off" or "On" is set here for the status display which appears during AWB operations. Return Use this to return to the previous menu. 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
48
Camera menu items
(continued)
IR Control [Disable, Enable]
“Enable” or “Disable” is set here for operations conducted
from the wireless remote control.
The operations are enabled when the unit’s power is
turned on from an external device other than a wireless
remote control, and they are disabled when the power is
turned on from a wireless remote control.
●
At the point when this item’s setting is changed, the
new setting is not reflected in operation.
It is reflected when the unit is set to standby mode
and its power is turned on.
●
Follow one of the procedures below if the item’s
setting is changed by mistake and the unit can no
longer be operated from a wireless remote control.
When menu operations can be performed using
another control device:
First change the item using a control device
capable of performing menu operations, and then
turn off the unit’s power and turn it back on.
When menu operations cannot be performed
using other control devices:
1.
Turn off the power of the units and devices that
are connected.
2.
Disconnect the unit’s AC adaptor cable and
LAN cable, and plug them back in.
3.
Perform the operation for turning on the unit’s
power from the wireless remote control.
4.
After changing this item, turn off the unit’s
power and turn it back on.
Notes
IR ID [CAM1, CAM2, CAM3, CAM4]
Configure the unit’s remote control ID.
The settings for this item correspond to the [CAM1] to
[CAM4] buttons on the wireless remote control.
Return
Use this to return to the previous menu.
■
Others 3/4 screen
###
Others
3/4
###
CAM/BAR
Camera
Bars Type
Type2
OSD Off With Tally
Off
OSD Status
Off
Return
CAM/BAR [Camera, Colorbar]
Switch between color bar display and camera image
display on the monitor and the web setup screen.
●
When the color bar is displayed, a test tone (1 kHz)
is output according to the Audio setting in the
camera menu.
Note
Bars Type [Type1, Type2]
Change the type of color bar to display.
Type1:
, Type2:
OSD Off With Tally [Off, On]
This is used to enable or disable the function for clearing
the OSD menu displays when the tally signal is received
by a command or contact.
When the tally signal is released, the original OSD menu
displays are restored.
OSD Status [Off, On]
“Off” or “On” is set here for the status display which
appears during AWB operations.
Return
Use this to return to the previous menu.