Panasonic AW-HS50 System Camera and Switcher Product Lineup Catalog - Page 50

Remote Camera System - Specifications Dimensions AW-HR140 *Specifications are subject to change without notice. General Synchronization System Power Requirements DC 12 V to 21.8 V (DC IN connector) DC 42 V to 57 V (PoE++ power supply) Current Consumption 3.1 A to 5.5 A (DC IN connector) 1.2 A (PoE++ power supply) Ambient Operating Temperature -15 °C to 45 °C (5 °F to 113 °F) (preheating is required when -5 °C (23 °F) or less) Ambient Operating Humidity 10% to 100% (no condensation) Storage Temperature -20 °C to 55 °C (-4 °F to 131 °F) Storage Humidity 10% to 95% (no condensation) Mass Approx. 9.0 kg (19.84 lb) Dimensions (W x H x D) 258 mm x 357 mm x 397 mm (10-5/32 inches x 14-1/16 inches x 15-5/8 inches) (including protrusions and cable cover) Finish Silver, salt resistant coating Waterproof and Dust Proof IP65 compliant Maximum Permissible Wind Speed 15 m/sec: Operates normally 50 m/sec: Operation possible 60 m/sec: No damage Wiper Installed as standard Heater Installed as standard Defroster Installed as standard Controller supported AW-RP120G, AW‑RP50, AK-HRP200G • It may be necessary to upgrade the version of the controller in order to support the unit. For details on upgrading, visit the support page on the following website. (http://pro-av.panasonic.net/) Camera Unit Imaging Sensors 1/2.86-type Full-HD 3MOS Lens Optical 20x zoom/10x digital zoom, F1.6 to F3.4 (f=4.5 mm to 90 mm; 35 mm equivalent: 32.13 mm to 642.5 mm) Focus Switching between auto and manual Focus Distance Entire zooming range: 800 mm (2.62 ft) Wide end: 400 mm (1.31 ft) Color Separation Optical System 3MOS Minimum Illumination 2 lx (50 IRE, F1.6, 36 dB, without accumulation) Horizontal Resolution 1000 TV lines Typ (Center area) Gain Selection Auto, 0 dB to 42 dB (1 dB steps) 37 dB to 42 dB is Super Gain Mode Frame Mix 0 dB, 6 dB, 12 dB, 18 dB, 24 dB • This cannot be configured when the format is 1080/29.97p, 1080/23.98p, 1080/29.97PsF, 1080/23.98PsF, 1080/25p, or 1080/25PsF. • When [Iris Mode] or [Focus Mode] is set to [Auto], this cannot be set to 18 dB or 24 dB. 59.94p / 1/100, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 59.94i 1/10000 Electronic Shutter Speed 29.97p 1/30, 1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 23.98p 1/24, 1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 50p / 50i 1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 25p 1/25, 1/60, 1/120, 1/250, 1/500, 1/1000, 1/2000, 1/4000, 1/10000 Synchro Scan 59.94 Hz 60.15 Hz to 642.21 Hz (255 steps) 50 Hz 50.15 Hz to 535.71 Hz (255 steps) Gamma HD, FILMLIKE1, FILMLIKE2, FILMLIKE3 0.30 to 0.75 (Manual setting) White Balance AWB A, AWB B, ATW, 3200K, 5600K, VAR (2000K to 15000K) Chroma Amount Variability OFF, -99% to 40% Synchronization System Internal/External synchronization (BBS/Tri-level sync) Input impedance High impedance Input Line Input Output • 2 channels, XLR balanced input • Input signal level: +4 dBu/0 dBu/-20 dBu (selectable in menu) • Volume variable range: -40 dB to +12 dB (can be changed in 1 dB steps in the menu) • 4 channels, superimposed over SDI output • Embedded audio output level: FS-12 dB: -12 dBFS, FS-18 dB: -18 dBFS, FS-20 dB: -20 dBFS (selectable in menu) • Sampling frequency: 48 kHz (synchronized to video) • Quantization bit rate: 24-bit (LPCM) • Audio compression format (IP): G.726, AAC-LC (High quality) Input Input Connector 12V IN XLR connector G/L IN BNC connector • BBS (Black Burst Sync), tri-level sync supported • Locking to a subcarrier is not possible with BBS. mini XLR connector (line input) Audio input #1: INPUT1 Common, #2: INPUT1 HOT, #3: INPUT1 COLD, #4: INPUT2 Common, #5: INPUT2 HOT, #6: INPUT2 COLD Output Video Output HD-SDI OUT SMPTE424/SMPTE292 standards 75 Ω (BNC x 2) • OSD output is possible from the SDI OUT 1/PM connector but not from the SDI OUT 2 connector. Input/Output Input/ Output Connector LAN RS-422 EXT LAN connector for IP control/video output/Audio output/ PoE++ power supply PoE++ (IEEE802.3bt Draft ver.2.0 standard) CONTROL IN RS-422A #1: DC GND, #2: HOT, #3: COLD, #4: 12V-OUT Pan-tilt Head Unit Installation Method Stand-alone (Desktop) or suspended (Hanging) • To ensure safety, the unit must be secured using the mount bracket supplied. Camera/ Pantilt Head Control IP connecting • When connecting through a PoE++ hub: LAN cable*1 (category 5e or above, straight cable), max. 100 m (328 ft) • When a PoE++ hub is not used: cable LAN cable*1 (category 5 or above, straight cable) max. 100 m (328 ft) AW series connecting cable/ LAN cable*1 (category 5 or above, straight cable), standard protocol max. 1000 m (3280 ft) connecting cable Pan/Tilt Operation Speed Maximum speed 60°/s or higher Panning Range ±175° • For suspended installations, the positions of the pins that determine the movement range must be changed. Tilting Range -30° to 210° • Depending on the pan or tilt position, the camera may be reflected in the image. • For suspended installations, the positions of the pins that determine the movement range must be changed. Quietness 60°/s (NC45 or less) Vibration Correction D.I.S.S. (Dynamic Image Stabilizing System) Standard Accessories Hexagonal bolt M8 x 30 mm: 4, M8 washer: 4, Spring washer: 4, Cable cover: 1, Washer nozzle mount bracket: 1, Drop-prevention wire: 1, Drop-prevention wire mounting screw (with hexagonal socket, for unit) M4 x 10 mm: 1 *1: Use of an STP (shielded twisted pair) cable is recommended. • When connecting directly to a controller without an Ethernet hub, use a cross cable. Scene File Scene1, Scene2, Scene3, Scene4 50 Intelligent Functions Auto function for each of accumulation, gain, iris, electronic shutter, ND, and ATW *For informations on "Output Signal Format", see page 38.