Panasonic AW-HS50 System Camera and Switcher Product Lineup Catalog - Page 75

Studio Camera System As of April, 2017 Synchronous Terminal Reference Input/ Output In gen-lock mode: Black burst or Tri-level Sync input signals (with loop-through) In internal sync mode: Black burst output signals x 2 • Same field frequencies as those of the system formats supported. • With the 1080/24PsF format, only gen-lock mode supported. • With the 1080/23.98PsF format, black burst with 10F-ID (SMPTE318M standard met) or TRI signals supported. 1 line (H) When the frame synchronizer setting is "Off" and the up-converter setting is "Off". Video Delay Time 1 frame (F) When the frame synchronizer setting is "On" or the up-converter setting is "On". • When the signals have passed through PinP, DVE, multi view, down-converter, DVI-IN or DVI-OUT, a maximum delay of 1 frame is applied in each case. Control Terminal LAN RJ-45 x 1 10BASE-T/100BASE-TX (For IP control) Connecting cable: LAN cable (category 5 or above), max. 100 m (328 ft), STP (Shielded Twisted Pair) cable recommended • When connecting to a hub (switching hub), use a straight cable. Use a crossover cable when connecting the unit and computer on a 1:1 basis without going through a hub. • Use with the same segment is recommended for the equipment which is connected to the unit. If the unit is connected to equipment whose segments are different, events dependent upon the settings inherent to the network equipment, for instance, may occur so thoroughly check the connections with the equipment to which the unit will be connected prior to the start of operation. EDITOR COM TALLY/GPI 1 TALLY/GPI 2 D-sub, 9-pin, female Used to control an editor RS-422 control connector Communication format Baud rate: 38400 bps Character length: 8 bit Parity: Odd Stop bit: 1 bit Flow control: None D-sub, 9-pin, female Used to control an external device RS-422 control connector Communication format (selected using a menu) • Mode: 1 (default setting) Baud rate: 9600 bps Character length: 8 bit Parity: None Stop bit: 1 bit Flow control: None • Mode: 2 Baud rate: 38400 bps Character length: 8 bit Parity: Odd Stop bit: 1 bit Flow control: None • Mode: 3 Baud rate: 38400 bps Character length: 8 bit Parity: None Stop bit: 1 bit Flow control: None D-sub, 15-pin, female ( x 2) Input: 8 inputs, general-purpose, photocoupler sensing Output: 19 outputs; selected from R/G tally, general-purpose Alarm: 1 output, open collector output (negative logic) Other BOOT switch [SV/NM (service/normal)] (for maintenance purposes) Normally, this switch is used as the "NM" position. Accessories CD-ROM (Operating Instructions , Operating Instructions , User Guide "AV-HS410 Image Transmission Software", DVI input level adjustment file (BW.bmp), Image Transmission Software (ImageTrans. exe)), Power cable (2 m [6.6 ft]) Remote Camera System Live Switcher AV-HS410 Block Diagram VIDEO PROCESS SDI 1- 4 SDI 5 - 8 ME BKGD MIX WIPE DVE(2ch) KEYER KEY PinP 1 PinP 2 Linear, Lum, Full PinP Chroma - - DVE DVE(2D) DVE(2D) EDGE Border Border Input Matrix Input Process DVI Internal Source •CBGD 1- 2 •CBAR •Black Video Memory •Still (V/K) 1- 2 •Clip (V/K) 1- 2 A1-A2 DSK AUX 1- 4 MV KEY Linear, Lum EDGE EDGE AUX 1 MIX transition AUX 2- 4 (CUT) B1-B2 Option Slot A-B Output Matrix SDI 1-5 DVI Control Panel A1-A2 B1-B2 75