Panasonic AW-HS50 System Camera and Switcher Product Lineup Catalog - Page 76
AW-HS50 - aw hs50n switcher
View all Panasonic AW-HS50 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 76 highlights
Live Switcher - Specifications AW-HS50 [AW-HS50N/E] General Power Requirements DC 12 V ±10 % (AC adaptor provided) Current Consumption 2.0 A (DC 12 V) Ambient Operating Temperature 0 °C to 40 °C (32 °F to 104 °F) Humidity 10 % to 90 % (no condensation) Dimensions (W x H x D) 210 x 67 x 177 mm (8-1/4˝ x 2-5/8˝ x 6-15/16˝) [excluding protrusions] Mass 1.4 kg (3.08 lbs.) Video Terminal Inputs Outputs SD Signal Formats HD Signal Processing ME Number SDI Inputs DVI-D Input SDI Outputs 5 video lines SDI 4 signal lines: SDI IN 1 to SDI IN 4 DVI-D 1 signal line: DVI IN 3 video lines, 4 outputs SDI 2 signal lines: SDI OUT 1, SDI OUT 2 (Only the SDI OUT 1 signals are split into two) DVI-D 1 signal line: DVI OUT 480/59.94i, 576/50i 1080/59.94i, 1080/50i, 720/59.94p, 720/50p, 1080/24PsF, 1080/23.98PsF Y:CB:CR 4:2:2, 10 bit (8 bits for frame memory) RGB 4:4:4, 8 bit 1ME HD: Serial digital component (SMPTE 292M) SD: Serial digital component (SMPTE 259M) 4 signal lines: SDI IN 1 to SDI IN 4 HD: SMPTE 292M (BTA S-004B) standard complied with • 0.8 V [p-p] ±10 % (75 Ω) • Input return loss More than 15 dB (5 MHz to 1.5 GHz) • Automatic equalizer 100 m (328 ft.) (when 5C-FB cable is used) SD: SMPTE 259M standard complied with • 0.8 V [p-p] ±10 % (75 Ω) • Input return loss More than 15 dB (5 MHz to 270 MHz) • Automatic equalizer 200 m (656 ft.) (when 5C-2V cable is used) Digital RGB (Vertical frequency: 60 Hz): XGA (1024 x 768), WXGA (1280 x 768), SXGA (1280 x 1024), WSXGA+ (1680 x 1050), UXGA (1600 x 1200), WUXGA (1920 x 1200) Digital RGB: 1080/50p, 1080/59.94p • Analog input signals are not supported. HD: Serial digital component (SMPTE 292M) SD: Serial digital component (SMPTE 259M) 2 signal lines: SDI OUT 1, SDI OUT 2 (Only the SDI OUT 1 signals are split into two) SDI Outputs DVI-D Output HD: SMPTE 292M (BTA S-004B) standard complied with • Output return loss More than 15 dB (5 MHz to 1.5 GHz) • Output level 0.8 V [p-p] ±10 % (75 Ω) • Rise time Less than 270 ps • Fall time Less than 270 ps • Difference between rise time and fall time Less than 100 ps • Alignment jitter Less than 0.2 UI (130 ps) • Timing jitter Less than 1.0 UI • Eye aperture ratio More than 90 % • DC offset 0±0.5 V SD: SMPTE 259M standard complied with • Output return loss More than 15 dB (5 MHz to 270 MHz) • Output level 0.8 V [p-p] ±10 % (75 Ω) • Rise time Less than 1.5 ns • Fall time Less than 1.5 ns • Difference between rise time and fall time Less than 0.5 ns • Jitter Less than 0.2 UI Digital RGB (Vertical frequency: 60 Hz): XGA (1024 x 768), WXGA (1280 x 768), SXGA (1280 x 1024), WSXGA+ (1680 x 1050), UXGA (1600 x 1200), WUXGA (1920 x 1200) Digital RGB: 1080/50p, 1080/59.94p • High-resolution multi view mode supported: Signals are also output with a high resolution even when SD has been selected as the system mode. When the high-resolution multi view mode is enabled, MV is assigned to the DVI OUT connector, and MV cannot be assigned to the SDI OUT 1 connectors or SDI OUT 2 connector. • Analog output signals are not supported. Synchronous Terminal Video Delay Time 1 frame (F) • Video signals that have passed through the PinP, multi view display, DVI-D input or DVI-D output will be delayed in each case by up to one frame. Control Terminal LAN TALLY/GPI RJ-45 x 1 10BASE-T/100BASE-TX (For IP control) Connecting cable: LAN cable (category 5 or above), max. 100 m [328 ft.], STP (Shielded Twisted Pair) cable recommended • When connecting to a hub (switching hub), use a straight cable. Use a crossover cable when connecting the unit and another device on a 1:1 basis without going through a hub. D-sub 15-pin, female, inch thread INPUT: 5 inputs, photocoupler sensing OUTPUT: 7 outputs, open collector output (negative logic) Other Other SERVICE switch [SV/NM] (for maintenance purposes) Normally, this switch is used as the "NM" position. Accessories Operating Instructions (this manual), CD-ROM (Operating Instructions , Operating Instructions , Data Transmission Software), AC adaptor, Power cable (2 m [6.6 ft.]) Output Matrix Input Matrix Input Process AW-HS50 Block Diagram SDI 1- 2 SDI 3 - 4 DVI Internal Source •CBGD •CBAR •Black Frame Memory •FMEM1-2 76 VIDEO PROCESS ME BKGD MIX WIPE KEYER KEY Linear, Lum Chroma EDGE PinP PinP DVE(2D) Border AUX AUX MIX transition MV SDI 1-2 DVI