Panasonic MC-UG323 Operating Instructions (Multi Language) - MCUG323 - Page 44

MC-V390B, Type UB12 around, rotating parts turn freely.

Get Panasonic MC-UG323 PDF manuals and user guides View all Panasonic MC-UG323 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Motor Shaft Arbre d'entrainement du moteur Eje del motor Belt Courroie Correa Agitator Agitateur Agitador ➢ Lay unit on floor bottom up with nozzle flat. ➢ Remove agitator by carefully lifting out. ➢ Remove worn or broken belt. ➢ Clean agitator and the end caps (see CLEANING AGITATOR, p. 46). Motor Shaft Arbre d'entrainement du moteur Eje del motor Belt Courroie Correa Agitator Agitateur Agitador End Cap Bouchon Tapa del extremo Groove Rainure Ranura ➢ Loop new belt (part number MC-V390B, Type UB12) around motor shaft and agitator belt groove. Make sure belt is routed in the belt guide as shown. See illustration for correct belt routing. ➢ Reinstall agitator back into nozzle by placing end caps into grooves. ➢ After reinstalling the agitator, turn it by hand to make sure that belt is not twisted or pinched and that all rotating parts turn freely. ➢ Place the vacuum in the upright position standing on the handle. This will minimize wheel interference when installing nozzle bottom plate. ➢ Reinstall nozzle cover by (1) aligning front edge of the cover with the nozzle and (2) rotating to installed position. 2 1 - 44 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
- 44 -
➢
Lay unit on floor bottom up with
nozzle flat.
➢
Remove agitator by carefully lifting
out.
➢
Remove worn or broken belt.
➢
Clean agitator and the end caps
(see CLEANING AGITATOR, p. 46).
Belt
Correa
Courroie
Motor Shaft
Arbre d’entrainement
du moteur
Eje del motor
Agitator
Agitateur
Agitador
➢
Loop new belt (part number
MC-V390B, Type UB12) around
motor shaft and agitator belt
groove.
Make sure belt is routed in
the belt guide as shown.
See
illustration for correct belt routing.
➢
Reinstall agitator back into nozzle
by placing end caps into grooves.
➢
After reinstalling the agitator, turn it
by hand to make sure that belt is
not twisted or pinched and that all
rotating parts turn freely.
Belt
Correa
Courroie
Motor Shaft
Arbre d’entrainement
du moteur
Eje del motor
End Cap
Tapa del
extremo
Bouchon
Agitator
Agitateur
Agitador
Groove
Rainure
Ranura
2
1
➢
Place the vacuum in the upright
position standing on the handle.
This will minimize wheel
interference when installing nozzle
bottom plate.
➢
Reinstall nozzle cover by (1)
aligning front edge of the cover with
the nozzle and (2) rotating to
installed position.