Samsung DV435GTGJRA/A1 User Manual Ver.1.0 (English, French, Spanish) - Page 20

Method 2

Get Samsung DV435GTGJRA/A1 PDF manuals and user guides View all Samsung DV435GTGJRA/A1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Installing your dryer Method 2 The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses. 1. If the "Y" connector cannot be attached directly to the cold water faucet, the short hose must be used. 2. Turn the cold water faucet off. 3. Attach the short inlet hose to the cold water faucet. Screw on the coupling by hand until it is seated on the faucet. 4. Using the pliers, tighten the coupling with an additional twothirds turn. Do not overtighten, as this may damage the coupling. 5. Attach the 'Y" connector to the brass male end of the small hose. Screw on the coupling by hand until it is seated on the connector. 6. Using the pliers, tighten the coupling with an additional twothirds turn. Short hose (Inlet to cold water) "Y" connector Long hose Duct Exhaust Frame (back) Do not overtighten, as this may damage the coupling. 7. Attach the angled end of long hoses to the fill valve at the bottom of the dryer rear frame. Screw on the coupling by hand until it is seated on the fill valve connector. 8. Using pliers, tighten the coupling with an additional twothirds turn. Water Hose Do not overtighten, as this may damage the coupling. 9. Attach the washer hose to the other side of the "Y" connector. Screw on the hose coupling until it is tight. Using pliers, tighten the coupling with an additional two thirds turn. Do not overtighten. You can damage the coupling. 10. Check that the water faucets are on. 11. Check for leaks around the "Y" connector, faucets and hoses. 20_ Installing your dryer DV435-02836G_EN_20120522.indd 20 2012-05-22 12:13:46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
20
_ Installing your dryer
Installing your dryer
Method 2
The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old
hoses.
1.
If the “Y” connector cannot be attached directly to the cold
water faucet, the short hose must be used.
2.
Turn the cold water faucet off.
3.
Attach the short inlet hose to the cold water faucet.
Screw on the coupling by hand until it is seated on the
faucet.
4.
Using the pliers, tighten the coupling with an additional two-
thirds turn.
Do not overtighten, as this may damage the coupling.
5.
Attach the ‘Y” connector to the brass male end of the small
hose. Screw on the coupling by hand until it is seated on the
connector.
6.
Using the pliers, tighten the coupling with an additional two-
thirds turn.
Do not overtighten, as this may damage the coupling.
7.
Attach the angled end of long hoses to the fill valve at the
bottom of the dryer rear frame. Screw on the coupling by
hand until it is seated on the fill valve connector.
8.
Using pliers, tighten the coupling with an additional two-
thirds turn.
Do not overtighten, as this may damage the coupling.
9.
Attach the washer hose to the other side of the “Y”
connector. Screw on the hose coupling until it is tight. Using
pliers, tighten the coupling with an additional two thirds turn.
Do not overtighten. You can damage the coupling.
10.
Check that the water faucets are on.
11.
Check for leaks around the “Y” connector, faucets and
hoses.
Short hose
(Inlet to cold
water)
“Y” connector
Long hose
Duct Exhaust
Frame
(back)
Water Hose
DV435-02836G_EN_20120522.indd 20
DV435-02836G_EN_20120522.indd
20
2012-05-22
12:13:46
2012-05-22
12:13:46