Samsung MultiXpress SCX-8248 User Guide - Page 239
Machine Setup, Scan System
View all Samsung MultiXpress SCX-8248 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 239 highlights
Message Prepare new Transfer roller. Punch hopper container is Full or not installed. Remove seal tape of [color/black] imaging unit and reinstall. Replace with new [color/black] imaging unit. Replace with new fuser unit. Replace with new Transfer roller. Replace with new [tray number] pickup roller. Replace with new MP pickup roller. Right door is open. Close it. Scanner locked or another problem occurred. Scan System Failure [error number]:Turn off then on. Second fax modem card is not installed. Install the card. Shake [color] toner cartridge. Meaning The estimated life of the transfer roller is close. The punch hopper container is full or not installed. The seal tape of the imaging unit is not removed. The indicated imaging unit has almost reached its estimated imaging unit life. The machine will stop printing. The life of the fuser unit expires totally. The life of the transfer roller expires totally. The life of the tray pickup roller expires totally. The life of the MP pickup roller expires totally. The door is not securely latched. The CCD (Charged Couple Device) lock has been locked. There is a problem in the scan system. The second optional fax multiline kit is not installed. Small amount of toner is left in the indicated cartridge. Suggested solutions Prepare a new transfer roller for a replacement. Empty the punch hopper container. Or install the punch hopper container. Remove the seal tape of the imaging unit (see "Replacing the imaging unit" on page 195). Replace the imaging unit with a Samsung-genuine imaging unit (see "Replacing the imaging unit" on page 195). Replace the fuser unit with a Samsung-genuine fuser unit. Replace the transfer roller with a Samsung-genuine transfer roller. Replace the tray pickup roller with a Samsung-genuine pickup roller. Replace the MP pickup roller with a Samsung-genuine MP pickup roller. Close the door until it locks into place. Unlock the CCD lock . Or turn the machine off and back on again. If the problem persists, call for service. Scanner Turn the machine off and back on again. If the problem persists, call for service. Install the optional fax multiline kit. If it is already installed, try to reinstall the optional fax multiline kit. If the problem persists, call for service. You may temporarily increase the printing quality by redistributing the toner (see "Redistributing toner" on page 188). Message Meaning Suggested solutions Side feeder door is open. Close it. Staple cartridge is empty. Replace it. Staple cartridge is low. Replace cartridge. Staple cartridge is not installed. Install it in finisher. Staple cartridge of booklet I is empty. Replace cartridge. Staple cartridge of booklet I is low. Replace cartridge. Staple cartridge of booklet I is not installed. Install the cartridge. The clock became initial time. Set a time again. Too much media in the center tray. Remove printed media. Too much media in booklet tray. Remove printed media. Too much media in finisher tray. Remove printed media. Top door of scanner is open. The door is not securely latched. The staple cartridge has reached the end of its lifespan. Small amount of staple cartridge is left. The estimated life of staple cartridge is close. The staple cartridge is not installed or the staple cartridge is not properly installed. The staple cartridge of booklet has reached the end of its lifespan. Small amount of staple cartridge of booklet is left. The estimated life of staple cartridge is close. The staple cartridge of booklet is not installed or the staple cartridge is not properly installed. The time setting of machine is initialized. The center tray is full. The booklet tray is full. The finishing tray is full. The duplex automatic document feeder cover is not securely latched. Close the door until it locks into place. This message appears when the staple cartridge is completely empty. Replace the staple cartridge. Prepare a new staple cartridge for a replacement. Install the staple cartridge. If it is already installed, try to reinstall the staple cartridge. If the problem persists, call for service. This message appears when the staple cartridge is completely empty. Replace the staple cartridge. Prepare a new staple cartridge for a replacement. Install the staple cartridge. If it is already installed, try to reinstall the staple cartridge. If the problem persists, call for service. Set the time setting in Machine Setup. Remove printouts from the center tray, the machine resumes printing. Remove printouts from the booklet tray, the machine resumes printing. Remove printouts from the finishing tray, the machine resumes printing. Close the cover until it locks into place. Troubleshooting_ 239