Sanyo PLC XU78 Owners Manual - Page 55

Lamp Replacement - bulb

Get Sanyo PLC XU78 - XGA LCD Projector PDF manuals and user guides
UPC - 086483068287
View all Sanyo PLC XU78 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Maintenance and Cleaning Lamp Replacement When the life of the projection lamp of this projector draws to an end, the LAMP REPLACE indicator emits a yellow light. If this indicator lights yellow, replace the lamp with a new one promptly. WARNING: TURN OFF THE UV LAMP BEFORE OPENING THE LAMP COVER This indicator is yellow when the life of the projection lamp draws to an end. Top Control CAUTION CAUTION Allow a projector to cool, for at least 45 minutes before you open the Lamp cover. The inside of the projector can become very hot. For continued safety, replace with a lamp of the same type. Do not drop a lamp or touch a glass bulb! The glass can shatter and may cause injury. Follow these steps to replace the lamp. 1 Turn off the projector and disconnect the AC power cord. Allow the projector to cool for at least 45 minutes. 2 Remove the screw with a screwdriver, and remove the lamp cover. Lamp Cover 3 Remove 2 screws of the lamp with a screwdriver and pull out the lamp upwards vertically by grasping the handle. 4 Replace the lamp with a new one and tighten the 2 screws back into position. Make sure that the lamp Screw is set properly. Replace the lamp cover and tighten the screw. Lamp 5 Connect the AC power cord to the projector and turn on the projector. 6 Reset the lamp replacement counter. See "Lamp Replacement Counter" on the next page . Screw Handle Screw ORDER REPLACEMENT LAMP Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the following information to the dealer. ● Model No. of your projector : PLC-XU75 / PLC-XU78 ● Replacement Lamp Type No. Service Parts No. : POA-LMP115 610 334 9565 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
55
Maintenance and Cleaning
When the life of the projection lamp of this projector
draws to an end, the LAMP REPLACE indicator emits
a yellow light.
If this indicator lights yellow, replace the
lamp with a new one promptly.
Lamp Replacement
WARNING:
TURN OFF THE UV LAMP BEFORE
OPENING THE LAMP COVER
Top Control
This indicator is yellow when
the life of the projection lamp
draws to an end.
For continued safety, replace with a lamp of
the same type.
Do not drop a lamp or touch
a glass bulb!
The glass can shatter and
may cause injury.
Allow a projector to cool, for at least 45
minutes before you open the Lamp cover.
The inside of the projector can become very
hot.
CAUTION
CAUTION
Follow these steps to replace the lamp.
Turn off the projector and disconnect the AC power
cord.
Allow the projector to cool for at least 45
minutes.
Remove ± screws of the lamp with a screwdriver
and pull out the lamp upwards vertically by
grasping the handle.
Replace the lamp with a new one and tighten the ±
screws back into position.
Make sure that the lamp
is set properly.
Replace the lamp cover and tighten
the screw.
Remove the screw with a screwdriver, and remove
the lamp cover.
Connect the AC power cord to the projector and
turn on the projector.
Reset the lamp replacement counter°
See "Lamp Replacement Counter" on the next
page .
1
2
3
4
5
6
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer.
When ordering a projection lamp, give
the following information to the dealer.
●
Model No. of your projector
: PLC-XU75 / PLC-XU78
●
Replacement Lamp Type No.
: POA-LMP115
Service Parts No.
610 334 9565
Lamp
Screw
Handle
Screw
Screw
Lamp Cover