Sanyo PLV Z700 Owners Manual - Page 41

To change the code of the projector, Remote control, Shutter demo, Power management - replacement lamp

Get Sanyo PLV Z700 - LCD Projector - 1200 ANSI Lumens PDF manuals and user guides
UPC - 086483072420
View all Sanyo PLV Z700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Setting Power management For reducing power consumption as well as maintaining the lamp life, the Power management function turns off the projection lamp when the projector is not used for a certain period. When this function is "On" and if the input signal is interrupted and no button is pressed for more than 30 seconds, the timer display with "No signal" appears on the screen. It starts the countdown until the lamp is turned off. The countdown time is set to five (5) minutes. When the countdown time has elapsed, the lamp is turned off to cool itself down. The POWER indicator is blinking red during the cooling-off period. When the lamp has been fully cooled down, the POWER indicator changes to green blinking. In this condition, the projection lamp can be turned on when the input signal is reconnected or any button on the top control or remote control is pressed. Press the Point 8 or OK buttons to switch On/Off. Remote control Two different remote control codes are assigned to this projector: the factory-set code (Code 1) and the secondary code (Code 2). This switching function prevents interference from other remote controls when several projectors or video equipment next to each other are used at the same time. When operating the projector in Code 2, the code for both the projector and the remote control must be switched to Code 2. To change the code of the projector: Press the Point 8 or OK buttons to switch between Code 1 and Code 2. To change the code of the remote control: Press and hold both the MENU and IMAGE ADJ. button on the remote control for more than 5 seconds to switch between Code 1 and Code 2. After changing the code, make sure the remote control operates properly. ✔Note: • When the batteries of the remote control are replaced, the remote control code automatically returns to the initial code (Code 1). Shutter demo Press the Point 8 or OK buttons to start Shutter demo. The automatic slide shutter closes once with the lamp being turned on and opens up again. This is used for checking the operation of the automatic slide shutter. ✔Note: • The Shutter demo function cannot be operated continuously. Once you started, it cannot be selected again for about five seconds. Power management Remote control Shutter demo The time left until lamp off 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
41
Two different remote control codes are assigned to this projector:
the factory-set code (Code 1) and the secondary code (Code 2).
This switching function prevents interference from other remote
controls when several projectors or video equipment next to each
other are used at the same time.
When operating the projector in Code 2, the code for both the
projector and the remote control must be switched to Code 2.
To change the code of the projector:
Press the Point
8
or OK buttons to switch between Code 1 and
Code 2.
To change the code of the remote control:
Press and hold both the MENU and IMAGE ADJ. button on the
remote control for more than 5 seconds to switch between Code
1 and Code 2.
After changing the code, make sure the remote control operates
properly.
Remote control
Shutter demo
Press the Point
8
or OK buttons to start Shutter demo. The
automatic slide shutter closes once with the lamp being turned on
and opens up again. This is used for checking the operation of the
automatic slide shutter.
✔
Note:
• When the batteries of the remote control are replaced, the remote
control code automatically returns to the initial code (Code 1).
Shutter demo
Remote control
For reducing power consumption as well as maintaining the lamp
life, the Power management function turns off the projection lamp
when the projector is not used for a certain period.
When this function is “On” and if the input signal is interrupted
and no button is pressed for more than 30 seconds, the timer
display with “No signal” appears on the screen. It starts the
countdown until the lamp is turned off. The countdown time is set
to five (5) minutes.
When the countdown time has elapsed, the lamp is turned off to
cool itself down. The POWER indicator is blinking red during the
cooling-off period. When the lamp has been fully cooled down,
the POWER indicator changes to green blinking. In this condition,
the projection lamp can be turned on when the input signal is
reconnected or any button on the top control or remote control is
pressed.
Press the Point
8
or OK buttons to switch On/Off.
Power management
The time left until
lamp off
Power management
✔
Note:
• The Shutter demo function cannot be operated continuously.
Once you started, it cannot be selected again for about five
seconds.
Setting