Sharp XR-32SL XR-32S XR-32X Operation Manual - Page 55

Appendix, Maintenance indicator, Problem, Cause, Possible Solution, Abnormal

Page 55 highlights

Maintenance indicator Temperature warning indicator Normal Off Abnormal Red on (Standby) Problem The internal temperature is abnormally high. Lamp indicator Green on (Green blinks when the lamp is warming up or turning off.) Red on The lamp does not illuminate. Time to change the lamp. Red on The lamp does (Standby) not illuminate. Power indicator Green on/ Red on Green blinks (Cooling) Red blinks The power indicator blinks in red when the projector is on. Cause • Blocked air intake • Cooling fan breakdown • Internal circuit failure • Clogged air intake • The lamp is shut down abnormally. • Remaining lamp life becomes 5% or less. • Burnt-out lamp • Lamp circuit failure • The lamp unit cover is open. Possible Solution • Relocate the projector to an area with proper ventilation. (See page 8.) • Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 65) for repair. • Disconnect the power cord from the AC outlet, and then connect it again. • Carefully replace the lamp. (See page 52.) • Take the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 65) for repair. • Please exercise care when replacing the lamp. • Securely install the cover. • If the power indicator blinks in red even when the lamp unit cover are securely installed, contact your nearest Sharp Authorized Projector Dealer or Service Center (see page 65) for advice. Info • If the temperature warning indicator illuminates, and the projector enters standby mode, follow the possible solutions above and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 10 minutes.) • If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again. • The cooling fan keeps the internal temperature of the projector constant and this function is controlled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction. Appendix 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73

51
Appendix
• If the temperature warning indicator illuminates, and the projector enters standby mode, follow the
possible solutions above and then wait until the projector has cooled down completely before plug-
ging in the power cord and turning the power back on. (At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using
the projector, and the power supply recovers immediately after that, the lamp indicator will illumi-
nate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet,
replace the power cord in the AC outlet and then turn the power on again.
• The cooling fan keeps the internal temperature of the projector constant and this function is con-
trolled automatically. The sound of the cooling fan may change during operation because the fan
speed may change and this is not a malfunction.
Maintenance indicator
Problem
The internal
temperature is
abnormally
high.
The lamp does
not illuminate.
Time to change
the lamp.
The lamp does
not illuminate.
The power
indicator blinks
in red when the
projector is on.
Cause
Blocked air intake
Cooling fan
breakdown
Internal circuit
failure
Clogged air intake
The lamp is shut
down abnormally.
Remaining lamp life
becomes 5% or
less.
Burnt-out lamp
Lamp circuit failure
The lamp unit cover
is open.
Possible Solution
Relocate the projector to
an area with proper
ventilation. (See page
8
.)
Take the projector to your
nearest Sharp Authorized
Projector Dealer or Service
Center (see page
65
) for
repair.
Disconnect the power cord
from the AC outlet, and
then connect it again.
Carefully replace the lamp.
(See page
52
.)
Take the projector to your
nearest Sharp Authorized
Projector Dealer or Service
Center (see page
65
) for
repair.
Please exercise care when
replacing the lamp.
Securely install the cover.
If the power indicator blinks
in red even when the lamp
unit cover are securely
installed, contact your
nearest Sharp Authorized
Projector Dealer or Service
Center (see page
65
) for
advice.
Abnormal
Red on
(Standby)
Red on
Red on
(Standby)
Red
blinks
Tempera-
ture
warning
indicator
Lamp
indicator
Power
indicator
Normal
Off
Green on
(Green
blinks
when the
lamp is
warming
up or
turning
off.)
Green on/
Red on
Green
blinks
(Cooling)
Info