TEAC DM-3200 DM-3200 Owner's Manual - Page 100

Viewing a list of location memories, Manual location, Repeat play, Press a number key

Get TEAC DM-3200 PDF manuals and user guides View all TEAC DM-3200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 100 highlights

8 - Remote operation : Location memories NOTE If a pre-roll time has been set ("Locate Preroll" on page 98), the controlled device will locate to the location memory point, minus the value set as the preroll time. Viewing a list of location memories To view a popup list of all the location memories which have been stored: • Press the LOCATE LIST key. Manual location It is also possible to enter a location point manually, (from a cue list, for instance) and locate straight to it. 1 Press the MANUAL key so that the indicator lights. 2 Use the number keys to enter a number in hh:mm:ss (and optionally frames) format. 3 When the ENTER key is pressed, the con- trolled device starts to locate to the location point just entered. Repeat play Location memories 8 and 9 (accessed with the 8 and 9 keys) are used as the start and end points of a repeat loop that can be played by pressing the REPEAT key in the MACHINE CONTROL section. While the repeat loop is in progress, the indicator flashes while the playback position is outside the • The location memory source (timecode or MTC) is shown, along with the value of each location memory. The DIRECT indicator also lights. • Press a number key (from 0 through 9) to locate to a location point on the list while the list is showing. This location point can be stored by pressing the MEMO key so that the indicator flashes, followed by pressing the MANUAL key again. To locate to this point again after storing the location point, press the MANUAL key, followed by the ENTER key. Note that the pre-roll time ("Locate Preroll" on page 98) does not apply here. loop points, and lights steadily while it is inside them. The repeat is always between points 8 and 9, regardless of their order. These points must be more than 5 seconds apart. 100 TASCAM DM-3200 User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
8 – Remote operation : Location memories
100
TASCAM DM-3200
User’s Manual
NOTE
If a pre-roll time has been set (“Locate Preroll” on
page 98), the controlled device will locate to the loca-
tion memory point, minus the value set as the preroll
time.
Viewing a list of location memories
To view a popup list of all the location memories
which have been stored:
•
Press the
LOCATE
LIST
key.
•
The location memory source (timecode or
MTC) is shown, along with the value of each
location memory. The
DIRECT
indicator also
lights.
•
Press a number key (from
0
through
9
) to
locate to a location point on the list while the
list is showing.
Manual location
It is also possible to enter a location point manually,
(from a cue list, for instance) and locate straight to it.
1
Press the
MANUAL
key so that the indicator
lights.
2
Use the number keys to enter a number in
hh:mm:ss
(and optionally frames) format.
3
When the
ENTER
key is pressed, the con-
trolled device starts to locate to the location
point just entered.
This location point can be stored by pressing the
MEMO
key so that the indicator flashes, followed by
pressing the
MANUAL
key again.
To locate to this point again after storing the location
point, press the
MANUAL
key, followed by the
ENTER
key.
Note that the pre-roll time (“Locate Preroll” on
page 98) does not apply here.
Repeat play
Location memories 8 and 9 (accessed with the
8
and
9
keys) are used as the start and end points of a repeat
loop that can be played by pressing the
REPEAT
key
in the
MACHINE CONTROL
section.
While the repeat loop is in progress, the indicator
flashes while the playback position is outside the
loop points, and lights steadily while it is inside
them.
The repeat is always between points 8 and 9, regard-
less of their order. These points must be more than 5
seconds apart.