TEAC DM-3200 DM-3200 Owner's Manual - Page 105

Dimensional drawing, Messages and troubleshooting

Get TEAC DM-3200 PDF manuals and user guides View all TEAC DM-3200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

Dimensional drawing 9 - Specifications : Dimensional drawing MMv MMv MMv MMv MMv MMv Figure 9.1: Dimensional drawing Messages and troubleshooting This provides an alphabetical list of the messages that you may see on the DM-3200, which provide information on the operation that you are performing. Not all of these messages are error messages. "Information" messages, i.e. those which pop up briefly and provide information about a change in status, etc., are marked with a ●. "Confirm" messages, where a response may be necessary (usually confirm with the ENTER key or can- cel with the cursor keys) are marked with a ✔. Messages demanding action other than a simple con- firmation are shown with a (✖), but even these do not necessarily indicate an error. Action ● ✖ ✖ ● ● ✔ Message Meaning Already assigned. Automation data and Current Status use different Fs. Press ENTER to continue. Automation data and Current Status have different timecode types. Press ENTER to continue. Automation data was recalled. Automation data was stored. AUX 1-2 Level Set up Ch parameters? Press ENTER to confirm, or a cursor key to cancel The RECORD key has already been assigned to a remote unit. The automation data uses a sampling frequency of a different value from the current sampling frequency. The automation data uses a timecode of a different frame type from the current timecode. The selected automation data has been recalled into memory. The current automation data has been stored to card. Used when batch copying parameters from channel to Aux 1-2 settings. Table 9.2: Popup messages TASCAM DM-3200 Owner's Manual 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
9 – Specifications : Dimensional drawing
TASCAM DM-3200 Owner’s Manual
105
Dimensional drawing
Messages and troubleshooting
This provides an alphabetical list of the messages
that you may see on the DM-3200, which provide
information on the operation that you are performing.
Not all of these messages are error messages.
“Information” messages, i.e. those which pop up
briefly and provide information about a change in
status, etc., are marked with a
●
.
“Confirm” messages, where a response may be nec-
essary (usually confirm with the
ENTER
key or can-
cel with the cursor keys) are marked with a
✔
.
Messages demanding action other than a simple con-
firmation are shown with a (
✖
), but even these do not
necessarily indicate an error.
Figure 9.1: Dimensional drawing
Action
Message
Meaning
●
Already assigned.
The RECORD key has already been assigned to a remote unit.
✖
Automation data and Current Status use
different Fs.
Press ENTER to continue.
The automation data uses a sampling frequency of a different value from the
current sampling frequency.
✖
Automation data and Current Status have
different
timecode types.
Press ENTER to continue.
The automation data uses a timecode of a different frame type from the current
timecode.
●
Automation data was recalled.
The selected automation data has been recalled into memory.
●
Automation data was stored.
The current automation data has been stored to card.
✔
AUX 1-2 Level
Set up Ch parameters?
Press ENTER to confirm,
or a cursor key to cancel
Used when batch copying parameters from channel to Aux 1-2 settings.
Table 9.2: Popup messages