Toshiba MW27F51 Service Manual - Page 25

: T BRAKE ARM/T BRAKE BAND Refer to Fig. 2-7-A

Get Toshiba MW27F51 PDF manuals and user guides View all Toshiba MW27F51 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

[OK] Tension Connect [NG] Tension Connect Tension Connect DISASSEMBLY INSTRUCTIONS Tension Band Tension Band Fig. 2-6-D NOTE 1. Take care not to damage the gears of the S Reel and T Reel. 2. The Polyslider Washer may be remained on the back of the reel. 3. Take care not to damage the shaft. 4. Do not touch the section "A" of S Reel and T Reel. (Use gloves.) (Refer to Fig. 2-8-A) Do not adhere the stains on it. 5. When you install the reel, clean the shaft and grease it. (If you do not grease, noise may be heard in FF/REW mode.) 6. After installing the reel, adjust the height of the reel. (Refer to MECHANICAL ADJUSTMENT) Main Chassis Fig. 2-6-E 2-7: T BRAKE ARM/T BRAKE BAND (Refer to Fig. 2-7-A) 1. Remove the T Brake Spring. 2. Turn the T Brake Arm clockwise and bend the hook section to remove it. 3. Unlock the 2 supports 1 and remove the T Brake Band. T Brake Band Idler Gear S Reel (B) (A) 1 Idler Arm Ass'y T Reel (A) 1 Hook section 1 T Brake Arm 1 T Brake Spring Fig. 2-8-A Fig. 2-7-A NOTE 1. In case of the T Brake Band installation, install correctly as Fig. 2-7-B. NOTE 1. In case of the S Reel and T Reel installation, check if the correct parts are installed. (Refer to Fig. 2-8-B) 2. In case of the Idler Arm Ass'y installation, install correctly as Fig. 2-8-C. And also set it so that the section "B" of Fig. 2-8-A is placed under the Main Chassis tab. [OK] T Brake Band [NG] T Brake Band T Brake Arm T Brake Arm Fig. 2-7-B 2-8: S REEL/T REEL/IDLER ARM ASS'Y/IDLER GEAR (Refer to Fig. 2-8-A) 1. Remove the S Reel and T Reel. 2. Remove the 2 Polyslider Washers 1. 3. Remove the Idler Arm Ass'y and Idler Gear. B2-3 Big Hole (S Reel) [OK] Clutch Gear [NG] Clutch Gear Small Hole (T Reel) Fig. 2-8-B Idler Arm Ass'y Idler Arm Ass'y Fig. 2-8-C

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
DISASSEMBLY INSTRUCTIONS
B2-3
Fig. 2-6-D
[OK]
[NG]
Tension Connect
Tension Band
Tension Connect
Tension Band
Fig. 2-6-E
Tension Connect
Main Chassis
2-7: T BRAKE ARM/T BRAKE BAND (Refer to Fig. 2-7-A)
Remove the T Brake Spring.
Turn the T Brake Arm clockwise and bend the hook
section to remove it.
Unlock the 2 supports
1
and remove the T Brake Band.
1.
2.
3.
Fig. 2-7-A
T Brake Band
Hook section
T Brake Arm
T Brake Spring
1
1
NOTE
1.
In case of the T Brake Band installation, install correctly
as Fig. 2-7-B.
Fig. 2-7-B
[OK]
[NG]
T Brake Arm
T Brake Band
T Brake Arm
T Brake Band
2-8: S REEL/T REEL/IDLER ARM ASS’Y/IDLER GEAR
(Refer to Fig. 2-8-A)
1.
2.
3.
Remove the S Reel and T Reel.
Remove the 2 Polyslider Washers
1
.
Remove the Idler Arm Ass’y and Idler Gear.
NOTE
1.
2.
3.
4.
5.
6.
Take care not to damage the gears of the S Reel and T
Reel.
The Polyslider Washer may be remained on the back of
the reel.
Take care not to damage the shaft.
Do not touch the section “A” of S Reel and T Reel. (Use
gloves.)
(Refer to Fig. 2-8-A)
Do not adhere the stains
on it.
When you install the reel, clean the shaft and grease it. (If
you do not grease, noise may be heard in FF/REW
mode.)
After installing the reel, adjust the height of the reel.
(Refer to MECHANICAL ADJUSTMENT)
Fig. 2-8-A
Idler Gear
Idler Arm Ass’y
S Reel
T Reel
(A)
1
1
(A)
NOTE
1.
2.
In case of the S Reel and T Reel installation, check if the
correct parts are installed.
(Refer to Fig. 2-8-B)
In case of the Idler Arm Ass’y installation, install correctly
as Fig. 2-8-C. And also set it so that the section “B” of
Fig. 2-8-A is placed under the Main Chassis tab.
Fig. 2-8-B
Big Hole
(S Reel)
Small Hole
(T Reel)
Fig. 2-8-C
[OK]
[NG]
Clutch Gear
Idler Arm Ass’y
Idler Arm Ass’y
Clutch Gear
(B)