Uniden UDR444 English Owner's Manual - Page 8

Attach the camera, Power Up the Monitor - security cameras

Get Uniden UDR444 PDF manuals and user guides View all Uniden UDR444 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

1. Hold the base of the camera stand where you want to mount it and mark the location of the screw holes. 2. Drill holes using the 5mm drill bit. 3. Insert anchors. 4. Use the included screws to attach the base to the wall or ceiling. You can also screw the base into a flat surface such as a tabletop if needed. 5. Before attaching the camera, tug gently on the stand to make sure it is securely in place. Attach the camera 1. For each camera, attach the camera bracket to the mounting screw. You can attach the stand to the top or 2 Tighten the brace against the camera to secure it in place. the bottom of the camera as needed. Tighten it a few turns, then turn the camera to face 3 the direction you want. Loosen the wingnut to 2. Tighten the camera brace up unlock the against the camera to secure it mounting post. into place. 3. Unlock the mounting post by turning the wingnut to the left a few turns. 4. Set the mounting post to the correct angle, then tighten the wingnut until the post is locked into place. 5. Attach the antenna to the rear of the camera. 1 Attach the camera to the mounting screw and turn it to the desired direction. 4 Adjust the post to the correct angle, then tighten the wingnut to lock the post into place. Power Up the Monitor 1. Press and hold the Power button on the left side of the monitor for 1 - 2 seconds to turn it on. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
8
1.
Hold the base of the camera stand where you want to mount it and mark the location
of the screw holes.
2.
Drill holes using the 5mm drill bit.
3.
Insert anchors.
4.
Use the included screws to attach the base to the wall or ceiling. You can also screw
the base into a flat surface such as a tabletop if needed.
5.
Before attaching the camera, tug gently on the stand to make sure it is securely in
place.
Attach the camera
1.
For each camera, attach
the camera bracket to the
mounting screw. You can
attach the stand to the top or
the bottom of the camera as
needed. Tighten it a few turns,
then turn the camera to face
the direction you want.
2.
Tighten the camera brace up
against the camera to secure it
into place.
3.
Unlock the mounting post by
turning the wingnut to the left
a few turns.
4.
Set the mounting post to the
correct angle, then tighten the
wingnut until the post is locked
into place.
5.
Attach the antenna to the rear of the camera.
Power Up the Monitor
1.
Press and hold the
POWER
button on the left side of the monitor for 1 - 2 seconds to
turn it on.
1
2
4
3
Loosen the
wingnut to
unlock the
mounting
post.
Attach the camera
to the mounting
screw and turn it
to the desired
direction.
Adjust the post to
the correct angle,
then tighten the
wingnut to lock the
post into place.
Tighten the brace against
the camera to
secure it
in place.