Viking VIPR161SS Installation Instructions - Page 8

Install Electrical Wiring, Install Cooktop - filter

Get Viking VIPR161SS PDF manuals and user guides View all Viking VIPR161SS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

VIKING RANGE CORPORATION Downdraft Ventilators INSTALL ELECTRICAL WIRING Interior Blower Installation ! CAUTION: All electrical wiring should be done by a qualified person(s) in accordance with all applicable codes and standards. 1. Mount a standard wiring box, with 3-pronged receptacle, inside the cabinet. Make sure the downdraft's power cord can easily reach it. 2. Run appropriate power cable into cabinet and connect it to receptacle. 3. Plug the downdraft's power cord into the outlet. Make sure that the power cord is routed away from the heat generated by the cooktop. INSTALL COOKTOP All Units 1. Align the cooktop with the downdraft and fasten cooktop in place. Note: Accurate alignment of cooktop and downdraft is necessary to ensure that there is no interference when air vent is raised and lowered.There should be a gap of 1/32" - 1/16" between the back of the cooktop and the front of the downdraft cover. Exterior Blower Installation ! CAUTION: All electrical wiring should be done by a qualified person(s) in accordance with all applicable codes and standards. 1. Mount a standard wiring box, with 3-pronged grounded receptacle, inside the kitchen cabinet. Make sure the downdraft's power cord can easily reach it. 2. Run appropriate power cabinet into cabinet and connect it to electrical box and receptacle. 3. Exterior blower may not exceed 6.0 Amp rating. 4. Run 2-wire plus ground power cable from the remote blower to wiring box on 10" round discharge plate. 5. Connect downdraft wiring to power cable from remote blower. Wire black to black, white to white, and green to green or bare wire. 6. Replace wiring box cover. 7. Plug the downdraft's power cord into outlet. Make sure that the power cord is routed away from the heat generated by the cooktop. "R" MODEL DOWNDRAFT REFSILETTER 1234 N UP/DOW TO RANGETOP REMOTE CONTROL MIN. FILTER 123 DOWUNP 4 COUNTERTOP Note: Rangetops and Designer Cooktops must be used with an "R" model downdraft (with remote control) - mounted into the 8 countertop, at least 4" from the burners.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
8
Downdraft Ventilators
VIKING RANGE CORPORATION
INSTALL ELECTRICAL WIRING
Interior Blower Installation
1.
Mount a standard wiring box, with 3-pronged receptacle, inside
the cabinet. Make sure the downdraft's power cord can easily
reach it.
2. Run appropriate power cable into cabinet and connect it to
receptacle.
3.
Plug the downdraft's power cord into the outlet. Make sure that
the power cord is routed away from the heat generated by the
cooktop.
!
CAUTION: All electrical wiring should be done
by a qualified person(s) in accordance with all
applicable codes and standards.
Exterior Blower Installation
1.
Mount a standard wiring box, with 3-pronged grounded recepta-
cle, inside the kitchen cabinet. Make sure the downdraft's power
cord can easily reach it.
2.
Run appropriate power cabinet into cabinet and connect it to
electrical box and receptacle.
3. Exterior blower
may not exceed
6.0 Amp
rating.
4. Run 2-wire plus ground power cable from the remote blower
to wiring box on 10" round discharge plate.
5.
Connect downdraft wiring to power cable from remote blower.
Wire black to black, white to white, and green to green or bare
wire.
6. Replace wiring box cover.
7.
Plug the downdraft's power cord into outlet. Make sure that
the power cord is routed away from the heat generated by the
cooktop.
!
CAUTION: All electrical wiring should be done
by a qualified person(s) in accordance with all
applicable codes and standards.
INSTALL COOKTOP
All Units
1.
Align the cooktop with the downdraft and fasten cooktop in
place.
Note:
Accurate alignment of cooktop and downdraft is necessary
to ensure that there is no interference when air vent is raised and
lowered. There should be a gap of 1/32" - 1/16" between the back
of the cooktop and the front of the downdraft cover.
FILTER
RESET
1
2
3
4
UP/DOWN
TO
1
2
3
4
FILTER
UP
DOWN
MIN.
Note:
Rangetops and Designer Cooktops
must be used with an
"R"
model downdraft (with remote control)
- mounted into the
countertop
, at least 4" from the burners.
RANGETOP
COUNTERTOP
REMOTE
CONTROL
"R" MODEL
DOWNDRAFT