Whirlpool 24-Inch Installation Instructions - Page 12

wiresarenotpinched. - blades

Get Whirlpool 24-Inch - Built-In Dishwasher (Color: Silver) Energy PDF manuals and user guides View all Whirlpool 24-Inch manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Determine Cabinet Opening Ifneedesde, ewebsitfeoranimateredpresentatoioftnhisstep. Visiwt ww.whirlpool.cuonmdeFrAQtab. Tightesntrainreliesfcrewtsosecurceord. Measure height of cabinet opening from underside of countertop to floor where dishwasher will be installed (you will need to measure the lowest point on the underside of the countertop and the highest point on the floor). Refer to "Dishwasher Height Adjustment Chart" for wheel position and the number of turns needed. Dishwasher Cabinet opening height 33% (86.0cm) 34 (86,4 cm) Height Adjustment I Wheel position Removed Number of turns on front leg I All the way up ! 1 I. 10 34!/4'i (8710 cm)2 NOTE: If the minimum cabinet opening height is less than 34" (86.4 cm), the rear wheels can be removed for additional clearance. This will allow the dishwasher to fit into a 337/8" (86 cm) high cabinet opening, but the dishwasher will be more difficult to move. (Measurements are approximate. Wheels and legs are preset at the factory for 341/2'' [87.6" crn].) Adjust wheels and legs 0 PlacweiresinsidteerminabloxI.nserttabson leftsideofcoveMr. akesurewiresaretuckedinsideboxC. lose coveernsurinwgiresarenotpincheUd.se1/4n"utdrivearnd previousrelymovesdcrewtosecurceover. NOTED:onotplugintooutleut ntiilnstructed. Turn both leveler legs to the same height. Put wheels in the required position determined from "Dishwasher Height Adjustment Chart." (To change wheel position, use a flat-blade screwdriver to pop out the wheel, then snap into the new position.) 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
Ifneeded,
seewebsite
foranimated
representation
ofthisstep.
Visit
www.whirlpool.com
under
FAQ
tab.
Tighten
strain
relief
screws
tosecure
cord.
0
Place
wires
inside
terminal
box.
Insert
tabson
leftsideofcover.
Make
surewiresare
tucked
insidebox.
Close
cover
ensuring
wiresarenotpinched.
Use1/4"
nutdriver
and
previously
removed
screw
tosecure
cover.
NOTE:
Donotplug
intooutlet
until
instructed.
Determine
Cabinet
Opening
Measure
height
of cabinet
opening
from
underside
of
countertop
to floor
where
dishwasher
will
be installed
(you
will
need
to measure
the
lowest
point
on the
underside
of the
countertop
and
the highest
point
on the floor).
Refer to
"Dishwasher
Height
Adjustment
Chart"
for wheel
position
and
the
number
of turns
needed.
Dishwasher
Height
Adjustment
Cabinet
I
Wheel
Number
of
turns
opening
height
position
on
front
leg
I
33%
(86.0cm)
Removed
All
the
way
up
I
34
(86,4
cm)
!
1
.
10
34!/4'i
(8710 cm)2
NOTE:
If the
minimum
cabinet
opening
height
is less than
34"
(86.4
cm), the
rear wheels
can be removed
for additional
clearance.
This will
allow
the
dishwasher
to fit into
a 337/8"
(86
cm) high
cabinet
opening,
but the
dishwasher
will
be more
difficult
to
move.
(Measurements
are approximate.
Wheels
and
legs
are preset
at the
factory
for 341/2'' [87.6"
crn].)
Adjust
wheels
and
legs
Turn
both
leveler
legs to the
same
height.
Put wheels
in the
required
position
determined
from
"Dishwasher
Height
Adjustment
Chart."
(To change
wheel
position,
use a flat-blade
screwdriver
to pop
out the wheel,
then
snap
into the
new
position.)
12