Whirlpool 24-Inch Installation Instructions - Page 15

Tip:Pushuponfront - washer

Get Whirlpool 24-Inch - Built-In Dishwasher (Color: Silver) Energy PDF manuals and user guides View all Whirlpool 24-Inch manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

IMPORTANIfwTh: eelws ereremovecdo,vetrhefloowr hen movintghedishwashtoear voidamagtoethefloorS. lowly movedishwashceormpleteinlytocabineotpeninDg.onotkinkor pinchwatelrined, rainhosep,owesrupplcyordordirecwt ire betweednishwashaenrdcabineRt.emovceardboafrdomunder dishwasher. NOTEIt:isallrighitf dishwashfietsrtightlyintocabineotpening. Donotremoviensulatiobnlanke- ttheblankeret ducethse sounldevel. NOTEIf:usingpowecrordm, akesuretorouteendthroughhole incutoubteforselidinigntocabineotpening. Alignfronot fdishwashdeoropr anewl ithfronot fcabinedtoors. Youmayneetdoadjusatlignmetnotbeevenwithyour cabinets. Placleevealgainstot pfrontopeninogftub.Check thatdishwashiselreveflromsidetosideI.fdishwashisenrot leveal,djusfrtontlegsupordownuntidl ishwashiseler vel. Connect to Water Supply Chectkhatlevelinleggsarefirmlyagaintshtefloor. Closaendlatchthedooar,ndplacleevealgainstht e fronpt aneCl.hectkhatdishwashisecrenterefrdomfrontoback intheopeninIgfn. eedeadd,juslet velinlegguntidl ishwashiser plumbR.epefaotrothesrideofdishwasher. HeJpfTuiJp:Pushuponfronot fdishwashtoeraisedishwasher offthegrountdoadjusfrtonltegsW. ithsomeinstallatioint s, maybeeasietor adjustht efronltegusintghe3A6h"exhead sockeotradjustabwlerench. Be sure rubber washer is properly seated in fitting. Slide the 3/4" fitting up to the valve and hand tighten to avoid unintentional cross-threading. Hand tighten until the coupling is tight. Using pliers, check the tightness of the coupling. An additional 1/4to 1/2 turn may be required to seal the rubber gasket. NOTE: Do not overtighten. Damage to the coupling can result. Place paper towel under 90 ° elbow fitting. Turn on water supply and check for leaks. If leak occurs, repeat previous step. If needed, see website for animated representation of this step. Visit www.whirlpool.com/watersupply FAQ tab. under NOTE: Do not use Teflon _>ttape with compression fittings. 1- _TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
IMPORTANT:
Ifwheels
were
removed,
cover
thefloor
when
moving
thedishwasher
toavoidamage
tothefloor.
Slowly
movedishwasher
completely
intocabinet
opening.
Donotkinkor
pinchwater
line,
drainhose,
power
supply
cordordirect
wire
between
dishwasher
andcabinet.
Remove
cardboard
fromunder
dishwasher.
NOTE:
Itisallright
ifdishwasher
fitstightly
intocabinet
opening.
Donotremove
insulation
blanket
- theblanket
reduces
the
sound
level.
NOTE:
Ifusingpower
cord,
make
sure
torouteend
through
hole
incutout
before
sliding
intocabinet
opening.
Align
front
ofdishwasher
door
panel
withfront
ofcabinet
doors.
Youmayneed
toadjust
alignment
tobeevenwithyour
cabinets.
Check
that
leveling
legsare
firmlyagainst
thefloor.
Close
and
latch
thedoor,
andplace
level
against
the
front
panel.
Check
thatdishwasher
iscentered
from
frontoback
intheopening.
Ifneeded,
adjust
leveling
leguntil
dishwasher
is
plumb.
Repeat
forother
sideofdishwasher.
HeJpfuJ
Tip:Pushuponfront
ofdishwasher
toraisedishwasher
offtheground
toadjust
front
legs.
Withsome
installations,
it
maybeeasier
toadjust
thefront
legusing
the3A6"
hexhead
socket
oradjustable
wrench.
Place
level
against
topfrontopening
oftub.Check
thatdishwasher
islevel
fromside
toside.
Ifdishwasher
isnot
level,
adjust
front
legsupordownuntil
dishwasher
islevel.
Connect
to Water
Supply
Be sure
rubber
washer
is properly
seated
in fitting.
Slide the 3/4"
fitting
up to the valve and
hand tighten
to avoid
unintentional
cross-threading.
Hand
tighten
until
the coupling
is tight.
Using
pliers, check
the tightness
of the coupling.
An additional
1/4to 1/2
turn
may be required
to seal the
rubber
gasket.
NOTE:
Do not overtighten.
Damage
to the coupling
can
result.
Place paper
towel
under
90 ° elbow
fitting.
Turn
on water
supply
and check
for leaks.
If leak occurs,
repeat
previous
step.
If needed,
see website
for animated
representation
of this
step. Visit
www.whirlpool.com/watersupply
under
FAQ tab.
NOTE:
Do not
use Teflon _>ttape
with
compression
fittings.
1-_TEFLON
is a registered
trademark
of
E.I. Du
Pont
De Nemours
and
Company.
15