Whirlpool 24-Inch Installation Instructions - Page 3

iNSTALLATiON REQUIREMENTS Tools and Parts Gather the recommended tools and parts before starting installation• Read and follow the instructions provided with any tools listed here. All Installations Tools needed: _,. Flat-blade • screwar!ver 5_ 1 _6 and V4 nut drivers or hex sockets _ _._Y" i.y UL histed/CSA _n Approved twist-on U W wire connectors* -- -- In addition, for first time installations Tools needed: Cordk with W!, 3/41' and 1Wi hole saw bits Parts needed: Copper tubing (%" O.D.suggested) or flexible braided cater su.._.l, lin _ _/f----__,_'_\ (,(.[t[.[L .)))))),)} I See '_Electrical Requirements" i . . F0rD,rectVV!re: ForP0wer section Supply useUL Listed/ CSA Approved Cord: use UL liste d power strain _elief SUPPLY cord kit to fit Y8 (2.2 cm)marked for use hg!e W!!h d!shwasher 10 adjustable wrench that opens to 11/8" (2.9 cm) _ s wrench . ,4 _ _..-_ *Must be the proper size to connect your household gauge wiring in dishwasher Other useful items you may need: wiring to 16 Flashlight _ Bath towel Parts supplied: hoDs_raCin!amps(2)_rainhose (! laige and I Small)I #10x1¢ Phi!!ips-head Green screws (2) Make sure all these parts are included in the literature package. Parts needed: Compr x _ Hose Fatting FOr part or kit, see local retailer or call Whirlpool Parts: 1-800-442.9991, Part Number w10273460 Other parts you may also need: 11V£"_2,': : (3811 z5cm) _ screw_type _ Sidem%unti_g kiWI Masking or_ for solid surface duct tape I I c°unter_°ps I I I clamps (3 maximum)18212560)!_-art lyU.mDe r [ I NOTE: Parts available for purchase in plumbing supply stores. Check local codes. Check existing electrical supply. See "Electrical Requirements" section. It is recommended that electrical connections be made by a licensed electrical installer. Location Requirements Grounded electrical supply required. Do not run drain lines, water lines or electrical wiring where they can interfere with or contact dishwasher motor or legs. The location where the dishwasher will be installed must provide clearance between motor and flooring. Motor should not touch the floor. Do not install dishwasher over carpeted flooring. Shelter dishwasher and water lines leading to dishwasher against freezing. Damage from freezing is not covered by the wa rra nty. A side panel kit is available from your dealer for installing your dishwasher at the end of your cabinetry. A moisture barrier accessory (Part Number 4396277)is available from your dealer for installing underneath the countertop. Check location where dishwasher will be installed. The location must provide: • easy access to water, electricity and drain. • Convenient access for loading and unloading dishes. Corner locations require a 2" (5.1 cm) minimum clearance between the side of the dishwasher door and the wall or cabinet. • square opening for proper operation and appearance. • cabinet front perpendicular to floor. • level floor. (If floor at front of opening is not level with floor at rear of opening, shims may be needed to level dishwasher.) Helpful Tip: Be sure to accurately measure dimensions and ensure dishwasher is level if the floor in the dishwasher opening is uneven (example: flooring extends only partway into opening). NOTE: To avoid shifting during dishwasher operation. shims must be securely attached to the floor. If dishwasher will be left unused for a period of time or in a location where it may be subject to freezing, have it winterized by authorized service personnel. Make sure pipes, wires and drain hose are within the shaded area shown in the "Product and Cabinet Opening Dimensions" section.