Whirlpool WHD3090G Owners Manual - Page 14

INSTALLATION INSTRUCTIONS, Installation Requirements

Get Whirlpool WHD3090G PDF manuals and user guides View all Whirlpool WHD3090G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

INSTALLATION INSTRUCTIONS Installation Requirements TOOLS AND PARTS Gather the required tools and parts before starting installation. Tools needed: Flat-blade screwdriver #2 Phillips screwdriver If using a power supply cord: Use a UL-listed power supply cord kit marked for use with clothes dryers. The kit should contain: ■■ A UL-listed 30-amp power supply cord, rated 120-/240-volt minimum. The cord should be type SRD or SRDT and be at least 4 ft. (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends. Additional Accessories: (Not supplied with dryer) Refer to "Operating Instructions" for information about accessories available for your dryer. Min. 8" long TORX® T20®† screwdriver 1/4" and 5/16" nut driver (recommended) Wire stripper (direct wire installations) Channel locks Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench Pliers Utility knife Tape measure Level 14 †® TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
14
INSTALLATION INSTRUCTIONS
Installation Requirements
TOOLS AND PARTS
Gather the required tools and parts before starting installation.
Tools needed:
Flat-blade screwdriver
#2 Phillips screwdriver
Wire stripper (direct wire
installations)
Channel locks
Adjustable wrench that
opens to 1" (25 mm)
or
hex-head socket wrench
1/4" and 5/16" nut driver
(recommended)
Utility knife
Tape measure
Level
Pliers
If using a power supply cord:
Use a UL-listed power supply cord kit marked for use with
clothes dryers. The kit should contain:
n
A UL-listed 30-amp power supply cord, rated 120-/240-volt
minimum. The cord should be type SRD or SRDT and
be at least 4 ft. (1.22 m) long. The wires that connect to
the dryer must end in ring terminals or spade terminals
with upturned ends.
Additional Accessories:
(Not supplied with dryer)
Refer to “Operating Instructions” for information about
accessories available for your dryer.
Min. 8" long TORX
®
T20
®†
screwdriver
†® TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.