Whirlpool WHD3090G Owners Manual - Page 20

Wire Power Supply Cord Strain Relief

Get Whirlpool WHD3090G PDF manuals and user guides View all Whirlpool WHD3090G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

3. Connect ground wire F F A Connect ground wire (F) (green or bare) of power supply cord under green external ground conductor screw (A). Tighten screw. 4. Connect remaining wires 3-Wire Power Supply Cord Connection Use where local codes permit connecting cabinet-ground conductor to neutral wire. 3-wire receptacle (NEMA-type 10-30R) 3 prong plug Spade terminals with upturned ends Ring terminals 1. Connect neutral (center) wire Connect remaining wires under outer terminal block screws. Tighten screws, tighten strain relief screws, and fold insulator over terminal block. Finally, reinsert tab of terminal block cover into slot at bottom edge of terminal block housing. Secure cover with the 2 hold-down screws. Now, go to "Level Dryer." 3-Wire Power Supply Cord Strain Relief: IMPORTANT: Use the strain relief supplied with the dryer. Attach power supply cord to strain relief B D C Connect neutral (center) wire (C) of power supply cord under center terminal block screw (B). Tighten screw. 2. Connect remaining wires Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. Do not further tighten strain relief screws at this point. 20 Connect remaining wires under outer terminal block screws. Tighten screws, tighten strain relief screws, and fold insulator over terminal block. Finally, reinsert tab of terminal block cover into slot at bottom edge of terminal block housing. Secure cover with the 2 hold-down screws. Now, go to "Level Dryer."

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
20
3-wire receptacle
(NEMA-type 10-30R)
3 prong plug
Spade terminals with
upturned ends
Ring terminals
4.
Connect remaining wires
Connect remaining wires under outer terminal block screws.
Tighten screws, tighten strain relief screws, and fold insulator
over terminal block. Finally, reinsert tab of terminal block cover
into slot at bottom edge of terminal block housing. Secure
cover with the 2 hold-down screws. Now, go to “Level Dryer.”
3-Wire Power Supply Cord Connection
Use where local codes permit connecting cabinet-ground
conductor to neutral wire.
2.
Connect remaining wires
Connect remaining wires under outer terminal block
screws. Tighten screws, tighten strain relief screws,
and fold insulator over terminal block. Finally, reinsert
tab of terminal block cover into slot at bottom edge
of terminal block housing. Secure cover with the
2 hold-down screws. Now, go to “Level Dryer.”
Connect neutral (center) wire (C) of power supply cord
under
center terminal block screw (B)
. Tighten screw.
3-Wire Power Supply Cord Strain Relief:
IMPORTANT:
Use the strain relief supplied with the dryer.
Attach power supply cord to strain relief
Put power supply cord through the strain relief. Be sure that
the wire insulation on the power supply cord is inside the
strain relief. Do not further tighten strain relief screws at
this point.
Connect ground wire (F) (green or bare) of power supply
cord under green external ground conductor screw (A).
Tighten screw.
3.
Connect ground wire
F
A
1.
Connect neutral (center) wire
B
C
D
F