Whirlpool WHD3090G Owners Manual - Page 24

Level Dryer, Complete Installation Checklist

Get Whirlpool WHD3090G PDF manuals and user guides View all Whirlpool WHD3090G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Level Dryer 1. Level dryer Place level here on either side Check levelness of dryer from side to side. Repeat from front to back. NOTE: The dryer must be level for the moisture-sensing system to operate correctly. If forward slope of dryer is greater than 1" (25 mm), water could run out from front of filter. 3. Plug into a grounded 3 prong outlet Not Level LEVEL 2. Adjust leveling legs Not Level If dryer is not level, prop up using a wood block, use wrench to adjust legs up or down, and check again for levelness. Once dryer is level, make sure all four legs are snug against the floor and dryer does not rock. 24 Complete Installation Checklist q Check that all parts are now installed. If there is an extra part, go back through steps to see what was skipped. q Check that dryer is level. See "Level Dryer." q Check that you have all of your tools. q Dispose of/recycle all packaging materials. q Check dryer's final location. q Remove any tape remaining on dryer. q Wipe dryer drum interior thoroughly with a damp cloth to remove any dust. q Read "Using Your Dryer" in "Operating Instructions." q For power supply cord installation, plug into a grounded outlet. For direct wire installation, turn on power. q Select a Timed Dry heated cycle and start dryer. If dryer will not start, check the following: • Controls are set in a running or ON position. • Start/Pause button has been pushed firmly and held for 3 seconds. • Dryer is plugged into an outlet and/or electrical supply. • Household fuse is intact and tight or circuit breaker has not tripped. • Dryer door is closed. This dryer automatically runs an installation diagnostic routine at the start of its first cycle. NOTE: You may notice an odor when dryer is first heated. The odor will go away.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
24
Level Dryer
1.
Level dryer
Place
level here on
either side
Not Level
LEVEL
Not Level
Check levelness of dryer from
side to side. Repeat from front to back.
NOTE:
The dryer must be level for the moisture-sensing
system to operate correctly. If forward slope of dryer is
greater than 1" (25 mm), water could run out from front
of filter.
2.
Adjust leveling legs
If dryer is not level, prop up using a wood block, use wrench
to adjust legs up or down, and check again for levelness.
Once dryer is level, make sure all four legs are snug against
the floor and dryer does not rock.
3.
Plug into a grounded 3 prong outlet
Complete Installation Checklist
q
Check that all parts are now installed. If there is an extra
part, go back through steps to see what was skipped.
q
Check that dryer is level. See “Level Dryer.”
q
Check that you have all of your tools.
q
Dispose of/recycle all packaging materials.
q
Check dryer’s final location.
q
Remove any tape remaining on dryer.
q
Wipe dryer drum interior thoroughly with a damp cloth
to remove any dust.
q
Read “Using Your Dryer” in “Operating Instructions.”
q
For power supply cord installation, plug into a grounded
outlet. For direct wire installation, turn on power.
q
Select a Timed Dry heated cycle and start dryer.
If dryer will not start, check the following:
• Controls are set in a running or ON position.
• Start/Pause button has been pushed firmly and held for
3 seconds.
• Dryer is plugged into an outlet and/or electrical supply.
• Household fuse is intact and tight or circuit breaker has
not tripped.
• Dryer door is closed.
This dryer automatically runs an installation diagnostic routine
at the start of its first cycle.
NOTE:
You may notice an odor when dryer is first heated.
The odor will go away.