Xerox 2135DT Service Guide - Page 190

Wiring Diagram connected to trays of up to 5th, including 2nd tray Large-Capacity Tray Paper Empty Paper Near Retard Sensor Empty Board A73 T6 Yellow T6 Blue Paper Width Sensing Board T11 Carrier Sensor Loading Sensor Lifter Sensor T5 Red T7 White (does not exist in the lowest) *1 connected to next tray (no tray in lowest section) Black Cover Opem SW T2 Blue T2 White T8 Red V73 Board T1 Blue ന T9 Blue T1 White Black White LTD/LTA Connector Offset PE Sensor Offset Sensor Offset Zero Sensor Carrier Clutch Tray lift (does not exist Motor in the lowest) Loading Clutch T3 White T10 Red Feed T4 Red (Hopping) Motor (does not exist in the lowest) Jam Sensor Operator Panel X71 Board Y5 Blown Y3 Red Y3 Yellow Y4 Green TNRK PANEL Y6 KPOW2 STUCK POWER TNRC TNRM T NRY P27 Y4 Y3 Y5 FDWPAP JOBOFFS Y71 Head JOBOFFPE YPOW2 Relay Board MPOW2 CPOW2 Y2 Blue Y1 White Face-down Stack Full Sensor P24 to P31 P27 P31 P26 P30 P25 P29 P24 P28 D D A A E E H H D D E E L L K Y D D A A E E H H D D E E L L M C Flex cable Sensor/Microswitch New NC2135 Connector connected to next tray (no tray in lowest section) Black 2nd Tray/3rd Tray Paper Empty Paper Near Empty Retard Sensor Board A73 T6 Yellow T6 Blue Paper Width Sensing Board T11 Carrier Sensor works as stepper Offset Motor Feed (Hopping) Motor Front/ Registration Motor K IDU Motor Loading Sensor T7 White LTD/LTA Lifter Sensor T5 Red Connector attached to motor *1 Cover Opem SW T2 Blue T2 White T9 Blue Tray lift Carrier Clutch T8 Red V73 Board T1 Blue ന P4 Yellow Black White T3 White T1 White T10 Red P4 Red Paper Width Sensor PAPWID P2 Yellow FFPOS P3 White P19 Red P17 Yellow Shutter Clutch SHUTTER Motor Loading Clutch T4 Red Feed (Hopping) Motor Pick PENDF P2 Blue OHP1 P2 Red Y IDU Motor Regist Clutch P17 P18 attached to clutch P19 P20 P1 P18 Blue P18 Red P18 Yellow P18 Black P19 White M IDU Motor C IDU Motor Belt Motor Fuser Motor P1 White P1 Yellow P5 Red Tray lift Motor P10 Brown Loading Sensor A73 Retard Sensor Board Lifter Sensor P6 Brown Carrier Sensor P20 White P20 Yellow Loading Clutch Pickup Clutch YPOW KPOW Y1200 K1200 CPOW MPOW C1200 M1200 OPTN P2 White P4 Green PEND PNEND P33 White P33 Blue P4 Blue/ Temperature Sensor P33 Green White SHU TTER FRPUCL HOPFF RCL BELTHET ID JOBOFF FACE Fan 3 (off-the-shelf) Fan 2 (power eject) Fan 1 (PU) attached to fan attached to fan attached to fan P17 Red DCL P2 REG K73 Main Board P4 TR1OP L-Side Color Registration Adjustment AOUT3 M7L Board R-Side Color Registration Adjustment AOUT2 M7R Board P7 Gray P7 Blue P7 Gray attached to fan FAN2 P5 P6 attached to fan P7 FAN1 FEED GE ARED CUIF RSNS P8 JODEN CPUFL N71 Board part of main motor assembly HOP(INSNS1) attached to SW1 sensor PARTTEMP PAPIN(INSNS2) Eject Sensor Heater PSWR(WRSNS) TNRFUL P9 Black P9 FCOVER FSENS COVOPN DUCOV P16 DUP_PAP MAIL TEMP R71 HUM Board HOPLIFT PSIZE DUPLEX HVOLT POWER STDUCOV P24 to P31 P23 S2 Fan 0 (power-on) Face-Down Solenoid Eject Solenoid I DPOSK I DPOSY I DPOSM I DPOSC Belt Fuse NBLT Contact points for Drum Contact Assemblies Duplex DUP-In Sensor DUP Front Sensor DUP Middle Sensor P14 P13 P12 P22 P21 P11 P10 P14 Red Y1 White S1 Gray S1 +5 VDC loop in this ribbon cable +5 VDC loop in this wiring harness Interconnect located by rear hinge Power harness Fan 0 (power eject) Low-Voltage Power Supply AC Input ACSW CN4-2,6-2 CN4-1,6-1 CN5 CN8 CN9 CN2 CN1 P13 Red Fuser Upper Thermistor THERM1 LHRTMP Sensor Fuser Lower Roller Thermistor THERM2 LBRTMP Heater Unit High-Voltage Power Supply Fuse NFU P16 Browm P15 Red P14 Yellow P12 Yellow D2 Yellow D2 Green D3 Blue V73 Board DUP Rear Sensor D1 Blue D1 White RemovedEdge Side Black White P11 Blue P11 White Upper Cover Open Microswitch (+38V cut) ̗̓̏ Paper Width Sensing Board PAPSIZ3-0 Face-up tray open switch Tray 1 Right Side Cover Open switch C73 I/F Board +5 VDC loop in this wiring harness Wiring diagram DUP Front Clutch DUP Rear Clutch DUP 0725-74 Service Guide 177