Yamaha LS9-32 Ls9 Editor Owner's Manual - Page 14

Ø Phase, HPF High Pass Filter, INS Insert, D. OUT Direct out, EQ Equalizer

Get Yamaha LS9-32 PDF manuals and user guides View all Yamaha LS9-32 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

D Ø (Phase) Inverts the phase of the signal after AD conversion. 4 E HPF (High Pass Filter) Switches the high pass filter on/off. You can drag the numeric value up or down to edit 5 the cutoff frequency. 6 F INS (Insert) 7 Enables/disables the insert-in. (INPUT CH 1-32 only) 8 G D. OUT (Direct out) Enables/disables the direct output. H EQ (Equalizer) Switches the EQ on/off. The graph immediately below the button shows the approxi- 9 mate response of the EQ. You can drag within the graph to edit the response of the EQ. To reset the EQ to flat response, hold down the (< >) key of your computer keyboard and click the graph (The HPF setting will remain). J I DYN1/DYN2 (Dynamics 1/Dynamics 2) Turns the two dynamics processors on/off. If Gate is assigned (Dynamics 1 only), the status of the gate is shown immediately below the button. Gate status indication On/off status On On On Off Open/closed status Closed Open Open - Remarks Gain reduction amount Gain reduction Gain reduction is 30 dB or more amount is 0-30 dB amount is 0 dB - If something other than Gate is assigned, a GR meter is shown immediately below the K button, and the amount of gain reduction is shown while this is on. The type for each dynamics processor can be selected in the Selected Channel window. L J MIX SEND M The bar graphs located immediately below the button show the send level of the signals sent from the INPUT N CH to VARI type MIX buses. You can also drag the bar graph to left or right to set the send level. While you drag the bar graph, the send level is shown in the numerical display area for PAN/TO STEREO MONO O (K). You can set the minimum value (-∞ dB) by holding down the (< >) key of your computer key- board and clicking the bar graph, or set the nominal value (0.00 dB) by holding down the (< >) key and key and clicking the bar graph. • Pre/on (green) P The bar graph display will change according to the • Pre/off (green) send position (pre/post) and on/off status of the signal sent from the INPUT CH to the MIX buses. • Post/on (yellow) Q To switch a send on/off, click the channel number located at the left of the bar graph. • Post/off (yellow) NOTE For FIXED-type MIX buses, the bar graph is fixed at nominal level (0 dB), and only the on/ off status is shown. 14 LS9 Editor Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
LS9 Editor Owner’s Manual
14
D
Ø (Phase)
Inverts the phase of the signal after AD conversion.
E
HPF (High Pass Filter)
Switches the high pass filter on/off. You can drag the numeric value up or down to edit
the cutoff frequency.
F
INS (Insert)
Enables/disables the insert-in. (INPUT CH 1–32 only)
G
D. OUT (Direct out)
Enables/disables the direct output.
H
EQ (Equalizer)
Switches the EQ on/off. The graph immediately below the button shows the approxi-
mate response of the EQ. You can drag within the graph to edit the response of the EQ.
To reset the EQ to flat response, hold down the <Ctrl>(<
>) key of your computer
keyboard and click the graph (The HPF setting will remain).
I
DYN1/DYN2 (Dynamics 1/Dynamics 2)
Turns the two dynamics processors on/off.
If Gate is assigned (Dynamics 1 only), the status of the gate is shown immediately below
the button.
If something other than Gate is assigned, a GR meter is shown immediately below the
button, and the amount of gain reduction is shown while this is on.
The type for each dynamics processor can be selected in the Selected Channel window.
J
MIX SEND
The bar graphs located immediately below the button
show the send level of the signals sent from the INPUT
CH to VARI type MIX buses. You can also drag the bar
graph to left or right to set the send level. While you
drag the bar graph, the send level is shown in the
numerical display area for PAN/TO STEREO MONO
(
K
).
You can set the minimum value (–
∞
dB) by holding
down the <Ctrl>(<
>) key of your computer key-
board and clicking the bar graph, or set the nominal
value (0.00 dB) by holding down the <Ctrl>(<
>)
key and <Shift> key and clicking the bar graph.
The bar graph display will change according to the
send position (pre/post) and on/off status of the signal
sent from the INPUT CH to the MIX buses.
To switch a send on/off, click the channel number
located at the left of the bar graph.
For FIXED-type MIX buses, the bar graph is
fixed at nominal level (0 dB), and only the on/
off status is shown.
Gate status
indication
On/off status
On
On
On
Off
Open/closed
status
Closed
Open
Open
—
Remarks
Gain reduction amount
is 30 dB or more
Gain reduction
amount is 0–30 dB
Gain reduction
amount is 0 dB
—
L
M
N
P
O
Q
K
J
4
6
7
8
5
9
• Pre/on (green)
• Pre/off (green)
• Post/on (yellow)
• Post/off (yellow)
NOTE