Yamaha LS9-32 Ls9 Editor Owner's Manual - Page 41

If a MATRIX channel is selected, CHANNEL SELECT Channel selection, FROM MIX, ST/MONO

Get Yamaha LS9-32 PDF manuals and user guides View all Yamaha LS9-32 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

If a MATRIX channel is selected ❏ CHANNEL SELECT (Channel selection) Except for the fact that your editing applies to a MATRIX channel, this is the same as the channel selection for a MIX channel (➥ p.37). ❏ FROM MIX, ST/MONO A FROM MIX, ST/MONO send level These adjust the send levels of the signals sent from the VARI type MIX buses or STEREO/MONO buses to the MATRIX bus. The current value is shown in the numerical box immediately below. • PRE/POST These select either PRE or POST as the position from which the signal is sent from the MIX buses or STEREO/ MONO buses to the MATRIX bus. PRE POINT is selected if this is on, or POST FADER is selected if this is off. B ON(FROM MIX, ST/MONO send on/off) These are on/off switches for the signal sent from the MIX buses or STEREO/MONO buses to the MATRIX bus. HINT • If MIX buses and MATRIX buses are being used in stereo, the odd-numbered knob will be PAN. PAN (odd-numbered side) • If the FIXED type is selected for the MIX bus, only the ON button is valid. • The stereo/mono setting and the VARI type / FIXED type setting can be made in the Mixer Setup screen. 41 LS9 Editor Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
LS9 Editor Owner’s Manual
41
If a MATRIX channel is selected
❏
CHANNEL SELECT (Channel selection)
Except for the fact that your editing applies to a MATRIX channel, this is the same as the channel selection for a
MIX channel (
➥
p.37).
❏
FROM MIX, ST/MONO
A
FROM MIX, ST/MONO send level
These adjust the send levels of the signals sent from the VARI type MIX buses or STEREO/MONO buses to the
MATRIX bus. The current value is shown in the numerical box immediately below.
• PRE/POST
These select either PRE or POST as the position from which the signal is sent from the MIX buses or STEREO/
MONO buses to the MATRIX bus. PRE POINT is selected if this is on, or POST FADER is selected if this is off.
B
ON(FROM MIX, ST/MONO send on/off)
These are on/off switches for the signal sent from the MIX buses or STEREO/MONO buses to the MATRIX bus.
•
If MIX buses and MATRIX buses are being used in stereo, the
odd-numbered knob will be PAN.
•
If the FIXED type is selected for the MIX bus, only the ON but-
ton is valid.
•
The stereo/mono setting and the VARI type / FIXED type setting can be made in the Mixer Setup screen.
HINT
PAN (odd-numbered side)