Yamaha MD8 Owner's Manual - Page 42

Single Take Auto Punch In/Out, Press the [AUTO PUNCH I/O] button.

Get Yamaha MD8 PDF manuals and user guides View all Yamaha MD8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

34 Recording & Mixing Techniques Single Take Auto Punch In/Out Rehearsing Auto Punch (Single Take) 1. Press the [REC SELECT] button (or [GROUP] + [REC SELECT]) of the track that you want to record. A dot flashes above the corresponding track indicator. 2. Press the [AUTO PUNCH I/O] button. 3. Select the Auto Punch In mode (Single Take) with the DATA dial and press [ENTER]. The Pre-Roll point (i.e., a position located 5 seconds before the Punch In point) is located automatically. The REHE indicators flash and the display shows A.Pnch Rehe . The AUTO PUNCH IN and OUT indicators appear. This is Single Take Auto Punch Rehearse Standby mode. If you're monitoring the track via CUE, you'll hear the signal that is assigned to the selected track. If you want to rehearse the Auto Punch In/Out repeatedly, press the [REPEAT] button. REPEAT appears on the display. 4. Press the [PLAY] button to start the Auto Punch In/Out sequence. Playback starts and the PLAY indicators light up. The REHE indicators continue to flash, indicating Play Rehearse Wait mode. At the specified IN point, punch in occurs (i.e., rehearsal starts). The REHE indicators stop flashing and light up continuously. The IN indicator disappears. If you're monitoring the track via CUE, you'll hear the existing sounds playback until the IN point, after which you'll hear the new sound that's going to be recorded (we're not recording anything in Rehearse mode, of course). At the specified OUT point, punch out occurs (i.e., rehearsal stops). The REHE indicators go out and the OUT indicator disappears. Playback continues up to the Post-Roll point. Then the Pre-Roll point is located automatically, and the MD8 waits in Auto Punch Rehearse Standby mode. You can press the [PLAY] button again for another rehearsal or move on to the next section to perform the Auto Punch In/Out for real. If you pressed the [REPEAT] button in Step 3, the MD8 will rehearse the Auto Punch In/Out repeatedly until you press the [STOP] button. The following illustration shows the Auto Punch Rehearse sequence. 8 7 6 5 4 REC 3 SELECT 2 1 Pre-Roll Point In Point Play Rehearse Wait Rehearse Out Point Post-Roll Point Play AUTO PUNCH I/O ENTER PLAY SINGLE TAKE IN OUT OUT MD8-Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
34
Recording & Mixing Techniques
MD8—Owner’s Manual
Single Take Auto Punch In/Out
Rehearsing Auto Punch (Single Take)
1.
Press the [REC SELECT] button (or [GROUP] + [REC SELECT]) of the track
that you want to record.
A dot flashes above the corresponding track indicator.
2.
Press the [AUTO PUNCH I/O] button.
3.
Select the Auto Punch In mode (Single Take) with the DATA dial and press
[ENTER].
The Pre-Roll point (i.e., a position located 5 seconds before the Punch In point) is located
automatically. The REHE indicators flash and the display shows
A.Pnch Rehe
. The
AUTO PUNCH IN and OUT indicators appear. This is Single Take Auto Punch Rehearse
Standby mode.
If you’re monitoring the track via CUE, you’ll hear the signal that is assigned to the selected
track. If you want to rehearse the Auto Punch In/Out repeatedly, press the [REPEAT] button.
REPEAT appears on the display.
4.
Press the [PLAY] button to start the Auto Punch In/Out sequence.
Playback starts and the PLAY indicators light up. The REHE indicators continue to flash,
indicating Play Rehearse Wait mode.
At the specified IN point, punch in occurs (i.e., rehearsal starts). The REHE indicators stop
flashing and light up continuously. The IN indicator disappears.
If you’re monitoring the track via CUE, you’ll hear the existing sounds playback until the
IN point, after which you’ll hear the new sound that’s going to be recorded (we’re not record-
ing anything in Rehearse mode, of course).
At the specified OUT point, punch out occurs (i.e., rehearsal stops). The REHE indicators
go out and the OUT indicator disappears.
Playback continues up to the Post-Roll point. Then the Pre-Roll point is located automati-
cally, and the MD8 waits in Auto Punch Rehearse Standby mode. You can press the [PLAY]
button again for another rehearsal or move on to the next section to perform the Auto Punch
In/Out for real.
If you pressed the [REPEAT] button in Step 3, the MD8 will rehearse the Auto Punch In/Out
repeatedly until you press the [STOP] button.
The following illustration shows the Auto Punch Rehearse sequence.
Pre-Roll
Point
3
4
5
6
7
8
2
1
Play Rehearse
Wait
Play
REC
SELECT
PLAY
ENTER
Rehearse
Post-Roll
Point
In
Point
Out
Point
AUTO
PUNCH I/O
IN
OUT
OUT
SINGLE TAKE