Yamaha MD8 Owner's Manual - Page 77

Erasing Parts, Use the CURSOR shuttle to select the tracks and the DATA dial to set

Get Yamaha MD8 PDF manuals and user guides View all Yamaha MD8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Erasing Parts 69 Erasing Parts The part Erase function allows you to erase a section of a track. The section to be erased is determined by the IN and OUT points. These points can be set by holding down the [SET] button while pressing [IN] or [OUT] respectively. Before Part Erase [IN] [OUT] Part Erase After Part Erase 1. Press the [EDIT] button and use the DATA dial to select the Part Erase function. 2. Press the [ENTER] button. If nothing happens, you haven't yet set the LAST REC IN and OUT points. See Setting the In/Out Points "On-the-Fly" on page 32 for more information. If you have not set the IN and OUT points, this function cannot be selected. 3. Use the CURSOR shuttle to select the tracks and the DATA dial to set the value either to * (do not erase) or to the number of the track in question. For example: **3**6**Tr . This means that the area between the IN and OUT points will be erased from tracks 3 and 6. 4. Press the [ENTER] button. The display shows Erase EXE? 5. Press [ENTER] again to erase. Press the [EXIT] button to cancel. The display shows Erase EXE. to signal that the Erase operation is performed. You can abort the Part Erase operation at anytime by pressing the [STOP] button. Data up to the point that you pressed the [STOP] button is erased. MD8-Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
Erasing Parts
69
MD8—Owner’s Manual
Erasing Parts
The part Erase function allows you to erase a section of a track. The section to be erased is
determined by the IN and OUT points. These points can be set by holding down the [SET]
button while pressing [IN] or [OUT] respectively.
1.
Press the [EDIT] button and use the DATA dial to select the Part Erase
function.
2.
Press the [ENTER] button.
If nothing happens, you haven’t yet set the LAST REC IN and OUT points. See
Setting the
In/Out Points “On-the-Fly”
on page 32 for more information.
If you have not set the IN and OUT points, this function cannot be selected.
3.
Use the CURSOR shuttle to select the tracks and the DATA dial to set the
value either to
*
(do not erase) or to the number of the track in question.
For example:
**3**6**Tr
. This means that the area between the IN and OUT points
will be erased from tracks 3 and 6.
4.
Press the [ENTER] button.
The display shows
Erase EXE?
5.
Press [ENTER] again to erase.
Press the [EXIT] button to cancel.
The display shows
Erase EXE.
to signal that the Erase operation is performed.
You can abort the Part Erase operation at anytime by pressing the [STOP] button. Data up
to the point that you pressed the [STOP] button is erased.
Before
Part Erase
After
Part Erase
Part Erase
[IN]
[OUT]