3Com 3CR17561-91-US Getting Started Guide - Page 52

Using Command Line Interface via Telnet, Telnet xxx.xxx.xxx.xxx, admin

Get 3Com 3CR17561-91-US - Switch 4500 26PORT Managed 24 10/100 2 Gbe Stackable RJ45 PDF manuals and user guides
UPC - 662705496238
View all 3Com 3CR17561-91-US manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

52 CHAPTER 3: SETTING UP FOR MANAGEMENT 4 To enter basic setup information for the Switch, select Administration > IP Setup and then follow the wizard through various system screens to enter the IP address and subnet mask that you want the Switch to use when it is connected to the network. The final page displays a summary of the information entered. 5 Select Save Configuration to save the configuration to your Switch. The initial set up of your Switch is now complete and the Switch is ready for you to set up your chosen management method. See "Methods of Managing a Switch" on page 42. Using Command Line Interface via Telnet 1 To start a Telnet session to the unit, click Start in Microsoft Windows 95/98/2000/NT/XP. a Click Run. b In the dialogue box that appears type the IP address of the unit, that is: Telnet xxx.xxx.xxx.xxx (where xxx.xxx.xxx.xxx is the IP address of the Switch) c Click OK. 2 Press Enter to open a login prompt. If the login prompt does not begin immediately, press Return a few times until it starts. 3 At the login and password prompts, enter admin as your user name and press Return at the password prompt. If you have logged on correctly, is displayed as shown in the example in Figure 20.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
52
C
HAPTER
3: S
ETTING
U
P
FOR
M
ANAGEMENT
4
To enter basic setup information for the Switch, select
Administration > IP
Setup
and then follow the wizard through various system screens to enter
the IP address and subnet mask that you want the Switch to use when it
is connected to the network. The final page displays a summary of the
information entered.
5
Select
Save Configuration
to save the configuration to your Switch.
The initial set up of your Switch is now complete and the Switch is ready
for you to set up your chosen management method. See “Methods of
Managing a Switch” on page 42.
Using Command Line Interface via Telnet
1
To start a Telnet session to the unit, click
Start
in Microsoft Windows
95/98/2000/NT/XP.
a
Click
Run
.
b
In the dialogue box that appears type the IP address of the unit, that
is:
Telnet xxx.xxx.xxx.xxx
(where xxx.xxx.xxx.xxx is the IP address of the Switch)
c
Click
OK
.
2
Press
Enter
to open a login prompt.
If the login prompt does not begin immediately, press Return a few times
until it starts.
3
At the login and password prompts, enter
admin
as your user name and
press
Return
at the password prompt. If you have logged on correctly,
<4500>
is displayed as shown in the example in Figure 20.