Acer F7200 User Manual - Page 18

Remote Control Operating Range, Projector and Remote Control Buttons

Get Acer F7200 PDF manuals and user guides View all Acer F7200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

ITEM 33. 34. LABEL 8 9 35. ID SET 36. Wired Jack DESCRIPTION SEE PAGE Number for Remote ID or password setting used. Number for Remote ID or password setting used. Press to set remote ID. Press ID SET for three seconds. The backlight on the remote control blinks, then press 01~99 to designate an ID. Press All and ID SET for five seconds. The backlight on the remote control blinks a single instance to reset control code to all, then can control all projector. Connect wire remote to the projector. Remote Control Operating Range The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15 degrees above or below the projector level. If the projector does not respond to the remote control, move a little closer. Projector and Remote Control Buttons The projector can be operated using the remote control or the buttons on the top of the projector. All operations can be carried out with the remote control; however, the buttons on the projector are limited in use. - 9 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
–
9
–
I
TEM
L
ABEL
D
ESCRIPTION
S
EE PAGE
33.
8
Number for Remote ID or password setting used.
34.
9
Number for Remote ID or password setting used.
35.
ID SET
Press to set remote ID.
Press
ID SET
for three seconds. The backlight on the remote control
blinks, then press 01~99 to designate an ID.
Press
All
and
ID SET
for five seconds. The backlight on the remote
control blinks a single instance to reset control code to all, then can
control all projector.
36.
Wired Jack
Connect wire remote to the projector.
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point
the remote directly at the projector. Provided you are not holding the remote perpendicular to the
sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23
feet) and 15 degrees above or below the projector level. If the projector does not respond to the
remote control, move a little closer.
Projector and Remote Control Buttons
The projector can be operated using the remote control or the buttons on the top of the projector.
All operations can be carried out with the remote control; however, the buttons on the projector
are limited in use.