Adaptec AAA-UDMA Hardware Guide - Page 46

Installing the Driver For a Fresh Installation of Windows 2000

Get Adaptec AAA-UDMA - RAID Controller PDF manuals and user guides View all Adaptec AAA-UDMA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

AAA-UDMA Installation and Hardware Guide Installing the Driver For a Fresh Installation of Windows 2000 To install the cdaudma.sys driver when you are installing Windows 2000, follow these steps: 1 Start your system with the Windows 2000 Boot CD-ROM in the CD-ROM drive. Note: When using a CD-ROM drive to install Windows 2000 from the bootable CD-ROM, make sure Bootable CD-ROM support is enabled. This is done through the System BIOS Setup utility. 2 Press F6 when this message is displayed: Press F6 if you need to install third-party SCSI drivers 3 Insert the Windows 2000 Driver disk for AAA-UDMA when the setup prompts you to insert the manufacturer supplied disk into drive A, and then continue. 4 Adaptec Array1000UDMA Family Manager Set for Windows 2000 driver will be displayed. Select this driver and continue with the rest of the Windows 2000 installation. 5 Your system will reboot once more to finish setting up Windows 2000. 6 When the Windows 2000 installation is complete, install Adaptec CI/O Management Software. Refer to the Adaptec CI/O Management Software User's Guide for instructions on installing and using the software. 5-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
5-4
AAA-UDMA Installation and Hardware Guide
Installing the Driver For a Fresh Installation of Windows
2000
To install the
cdaudma.sys
driver when you are installing Windows
2000, follow these steps:
1
Start your system with the Windows 2000 Boot CD-ROM in the
CD-ROM drive.
Note:
When using a
CD-ROM drive to install Windows 2000
from the bootable CD-ROM, make sure Bootable CD-ROM
support is enabled. This is done through the System BIOS
Setup utility.
2
Press
F6
when this message is displayed:
Press F6 if you need to install third-party SCSI drivers
3
Insert the Windows 2000 Driver disk for AAA-UDMA when
the setup prompts you to insert the manufacturer supplied
disk into drive
A
, and then continue.
4
Adaptec Array1000UDMA Family Manager Set for Windows
2000
driver will be displayed. Select this driver and continue
with the rest of the Windows 2000 installation.
5
Your system will reboot once more to finish setting up
Windows 2000.
6
When the Windows 2000 installation is complete, install
Adaptec CI/O Management Software. Refer to the
Adaptec CI/O Management Software User’s Guide
for instructions
on installing and using the software.