Adaptec AAA-UDMA Hardware Guide - Page 48

Windows 2000 Installation and Configuration Notes, Windows 2000 Disk Management

Get Adaptec AAA-UDMA - RAID Controller PDF manuals and user guides View all Adaptec AAA-UDMA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

AAA-UDMA Installation and Hardware Guide 13 When the driver is copied on the hard drive, click on the Finish button. 14 You will be prompted to restart the computer. Select Yes. 15 After rebooting the system, install the Adaptec CI/O Management Software. Refer to the Adaptec CI/O Management Software User's Guide for instructions on installing and using the software. Windows 2000 Installation and Configuration Notes Windows 2000 Disk Management When creating a new array on a system running under Windows 2000, the array is not listed in Windows 2000 Disk Management until the array is initialized. This is normal Windows 2000 functionality. Boot Order In Windows 2000 vs. ARRAYCONFIG UDMA During Windows 2000 installation, Windows 2000 does not show the devices in the boot order. Instead, it shows the arrays with the lower ID first. To minimize confusion during Windows 2000 installation, try one of the following: s Disconnect all devices other than members of the boot array, so that only one logical device is present in the Windows 2000 installation. Reconnect all other devices after Windows 2000 is successfully installed. s Configure the boot array in the ARRAYCONFIG UDMA utility so that the lowest ID is a member of the boot array. 5-6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
5-6
AAA-UDMA Installation and Hardware Guide
13
When the driver is copied on the hard drive, click on the
Finish
button.
14
You will be prompted to restart the computer. Select
Yes
.
15
After rebooting the system, install the Adaptec CI/O
Management Software. Refer to the
Adaptec CI/O Management
Software User’s Guide
for instructions on installing and using
the software.
Windows 2000 Installation and Configuration
Notes
Windows 2000 Disk Management
When creating a new array on a system running under Windows
2000, the array is not listed in Windows 2000 Disk Management until
the array is initialized. This is normal Windows 2000 functionality.
Boot Order In Windows 2000 vs. ARRAYCONFIG UDMA
During Windows 2000 installation, Windows 2000 does not show
the devices in the boot order. Instead, it shows the arrays with the
lower
ID first. To minimize confusion during Windows 2000 instal-
lation, try one of the following:
■
Disconnect all devices other than members of the boot array, so
that only one logical device is present in the Windows 2000
installation. Reconnect all other devices after Windows 2000 is
successfully installed.
■
Configure the boot array in the
ARRAYCONFIG UDMA
utility so that the lowest ID is a member of the boot array.